Відео

Wolfcraft 6952000 Esquadro 3d angular de laminado para umas medições exatas amzn.eu/d/9njUyGC

Thank you, yes it would look great. I thought about it, maybe i'll do it in the future.

Could an l.e.d light be wired into the power of the module?

@@kiwiace625 Yes, if it uses 12V

Ok read the other responses to that same question. The radio is exactly as it was found no ripping was done

@@AtticBuilds o, it looked like it was, my bad

No worries, you are actually the 1st to akcnowledge that.

It will depend on the board used, assuming it as a volume control I think it should be possible.

Yes it's exactly that, the other speaker was dead anyway.

I cavi sono stati sostituiti da quelli interi, quindi ho usato le altre uscite. Grazie per il commento.

@@AtticBuilds Grazie per la risposta, il modulo ha due uscite per due altoparlanti, quindi presuppongo che facciano effetto stereo, tu hai collegato soltanto un uscita e l'hai collegato all'unico altoparlante della radio, come si sente con un solo altoparlante? Grazie ancora

I think it's about 2 mm

It's a cheap board so about 10 euros

Thank you?

Actually it's a 10 bucks "conversion"

Really, and how many "valves" did you see inside...

@@AtticBuilds Yes really. I saw none ... no valves but I said waste of a "valve amp and tuner" not a waste of "valves". As the chassis is still there but stripped clearly someone butchered it to put in a cheap shitty two bob Chinese Bluetooth board with equally rubbish integrated amp. Probably because the valve amp was too complicated/High current to maintain/repair. I notice the original speaker is used too but not the tweeter ....probably because its electrostatic and needs more current than that board has so and more complicated wiring .... that still wouldnt sound 1/10th as good as the original valve equipment. As I said .. a good sounding radio ruined. It would've been so much better just putting a Bluetooth board in and activating it through the phono circuit and powered by the original valve amp, couldve also retained the tuner and volume control on the front knob instead of fancying about with the small button on a phone. If you can wire a plug you can do whats in this video but you'll be making something with a great tone sound mediocre and be more complicated to use. You haven't "repurposed" or "upcycled" anything here ... you've simply ruined something nice because it was far easier.

@@Rush-gz9sx The radio is exactly as it was found, so I saved it from the trash and gave it a new life. Now it sits on my living room mostly as a decoration piece as I don't even listen to music so much. You clearly missed the point of the video, the fact that's easy to do is the point, as not everyone is as capable as you sound.

@Attic Builds the radio isn't as found. They didn't come from the factory with the internals absent and just a chassis. So as I said above "clearly someone butchered it" whether it was you or a previous owner ... its been butchered. The 50s to early 60s German valve radios were the best in the world at the time ... by quite some margin. In fact only unnecessarily expensive solid state audio today can get close to the sound of a well sorted valve amp. Nordmende was one of the middle to upper brands. I think yours is a 1959 Rigaletto and was lower to middle of their range. The Rigaletto is quite a rare model now as everyone wants the top of the range Tannhauser model... so even more of a shame its missing its very essence. Whoever stripped it instead of fixing it ruined a very good radio. I stand by what I said.

@Rush2005 You clearly like to miss the obvious, either you don't understand or don't want to. So let me make this very easy... You win.

The idea of adding a light as crossed my mind. Using the volume knob or switching it on using the original buttons is a bit too advanced for me.

So the fact the radio is just a box with most components inside missing doesn't matter... You may dislike all you want but the fact is that this old radio was saved from the trash.

@@AtticBuilds you didn't save the radio. You re-purposed it, using the box and speakers. And that's ok. I didn't know the radio was already totally empty except for a metal chassis and some speaker . So I can only blame the one who cannibalised this radio before you.

The video is intended as a demonstration of simple and quick way to bring life to these old radios rather than go buy one "old looking" modern radio. I didn't even screw the board down, just hot glued it to keep the radio exactly as it was before.

You need to get a power supply. Yes the bluetooth is part of circuit board.

@@AtticBuilds is it just any old 120v single pin power supply?

I used an old 12 V DC power supply with 3.5 jack, it will run from 8 to 25 V.

Thanks so much for your comment. Actually I will release a new video soon.

I got this one from banggood banggood.com/50W+50W-TDA7492-CSR8635-Wireless-bluetooth-4_0-Audio-Receiver-Amplifier-Board-NE5532-Preamp-p-1109777.html?cur_warehouse=CN

Still learning to weld, but it all came together nicely. The angle grinder is my best friend 😀

Probably copyright issues. The sound as expected isn't that good,after all it's a cheap board. Thanks for the support.

@@AtticBuilds so what's the point making a radio with a bad sound? putting in a bluetooth speaker for 20€ would be even better then.

@@zerobambiro And if I told you that I only listen to music in the car, now that is mindblowing...

Thanks for the sugestion, and for commenting.

The board uses a power supply from DC 8 to 25V, I think I used an old 12V adapter.

50W+50W TDA7492 CSR8635 Wireless bluetooth 4.0 Audio Receiver Amplifier Board NE5532 Preamp Module Board from Electronic Components & Supplies on banggood banggood.app.link/n8D6BpcEujb

So saving an old radio from the trash is a crime...

Nice touch to be honest, the enhancement barely touched the original hardware and the Bluetooth transmitter can be taken off easily. Well played 😉

Not really. I have just converted a very similar Grundig model. If I had got it running, what medium, long or shortwave stations are still available? My plan was to leave the old interior intact. But as I accessed different areas inside the box, old plastic just crumbled. Pulleys broke at the touch. It looks great, sounds great, lights up like the original.

The radio chassis had been touched, the mains and output transformers as well as valves have been removed.

I didn't destroy it so... I really don't understand your comment...

I think it's repairable, that's why I left all the inside intact. The radio is more of a decorative piece, and it looks amazing. Thanks for watching and commenting.

@@AtticBuilds Repairable? It has nothing at all inside anymore !

Yes, just like I found it when I saved it from the trash...

It's just any bluetooth speaker so I assume it will do that. I have it disconnected and then ask google to "play music on the old radio". It will turn on and connect the Bluetooth and play music.

@@AtticBuilds Ok, great. I'm trying to find out which one suit's best for my old boombox. I think this one will do the trick. Thanks!

Proof most can not live without that phone!

This is a cheap board the sound isn't that good as expected. I think with a more advanced board it would be possible.

Buy a working vintage radio and plug your Bluetooth box to the aux

@@BavarianM What vintage radios have aux jacks my dude? They didn't start showing up til like the late 90s/early 2000s

@@geologicksome of the higher end radios back then came with phono ports for plugging in record players and stuff and you can get phono to aux adapters then add an aux Bluetooth receiver from there

Yes, it lacks some parts and I lack the knowledge 🙄. It's basically a bluetooth speaker with that vintage look. Probably in the future I will modifiy it to turn on with the original button and add some led lights to light up the display.

Thanks

Thanks for your comment

As for experience I have zero so anyone can do it 😉. The buzz in the speaker probably means it's not in perfect condition, but that is to expected after all it is a 40's radio. You can replace it with a new one. But I probably would mantain all intact and add a new speaker directly connected to the Bluetooth board.

The buzz could be interference from a switched mode power supply, or a defective H.T smoothing capacitor. No, putting the Bluetooth amplifier onto the radios original speaker should not be done because the amplifier is stereo and the radio only has one main speaker. Also the impedance of the speaker and amplifier do not match. The radio speaker is only rated at 6 watts and the amplifier will be more.

It's about 1957. The buzz will be either RF interference or a duff H.T smoothing capacitor.

Yes it can, and it looks so much better than those fake vintage bluetooth radios.

@@AtticBuilds it's still garbage as you threw away all the tube Eletrónics that make it worth it

@@BavarianM Yes it's a beatiful piece of "garbage" decorating the living room. As for the valves and all that precious stuff inside, they were long gone when I found the radio and saved it from the trash...what a crime....

Thanks for commenting in future videos I'll do that thanks.

I'm using a 12 V power adapter, the specs are 8 to 25 V so anything in between will do the job. I'm glad to see someone inspired to do this and save another of these old radios from the trash👍

@@AtticBuilds You are so right. In the days they made beautiful radio's. I am looking for one which doesn't work anymore and re-animate it ;)

Today I bought a Telefunken: Allegro 2183. It’s in mint condition from the outside. From the inside it’s dead. But I will try to fix it. There are 3 speakers inside. What’s the best way to connect the card? www.radiomuseum.org/r/telefunken_allegro_2183_1.html This is a working radio, same as mine. ua-cam.com/video/IDaIhn5GwS8/v-deo.html I am looking for a light for inside which will light the front panel. And I will look for a small blue light as seen in the original one... 😋

If all the speakers work, you could connect the middle one to one channel and one or maybe the two in the sides to the other channel. Test it out mine is using only one speaker and works fine, it's not stereo though. But for the board low price the sound quality is not amazing, so... I decided to do this project so this old radio would become more than just decoration.

@@AtticBuilds That's a GREAT idea. I will try that when I receive the card. I also think to place a led strip at the back which goes inside too to provide the inner part of the radio too.