- 50
- 175 866
DCrMotorsport_Silent
United States
Приєднався 15 вер 2006
Car performance enthusiast, Specializing in Fabrication, modifications & Engine building. Channel will cover some of these topics, and maybe more, and sharing the knowledge and experience i gained way..
Custom H Pattern Honda shifter conversion with money shift lockout mechanism
Honda TSX ebay shifter converted to Mitsubishi, with custom 1-2-1 lockout and 2-3-2 lockout. Testing flatshift with lockout
#honda #mitsubishi #fabrication
#honda #mitsubishi #fabrication
Переглядів: 515
Відео
Honda K Series Swapped Toyota Levin
Переглядів 1 тис.Рік тому
K Series engine and gearbox swapped into Toyota Levin. Using an eg k series mount swap kit to modify and adjust to fit the chassis #kswap #toyota #engineswap
Mitsubishi Evo Colt Link G4X Ecu Install & Tune
Переглядів 1,3 тис.Рік тому
Installation & Tuning off a PNP Link G4X Evo Ecu in an AWD Mitsubishi Colt Purchased from Maxtorqueperformance.com Official Link Dealer #linkecu #mitsubishi #turbo
Evo Swapped BMW e46 Drift car Part 2 - Angle Kit, Rear Diff X Brace & Chassis Reinforcement
Переглядів 647Рік тому
Gravity Performance Steering Angle Kit installation, and Chassis Reinforcement Plates with X Brace #drift #4g63 #bmw
Honda K Series Side Exit Header Fabrication
Переглядів 1,3 тис.Рік тому
First time trying my hand at a N/A Header, was curious to see how it comes out.
2ZZ-GE Celica Engine Swapped Toyota Vitz!
Переглядів 6 тис.Рік тому
Swapping and fabricating mounts to fit toyota's 2zz engine into a tiny little vitz's engine bay #2zzge #toyota #engineswap
Street digs 3 - From the streets to the track!
Переглядів 1,4 тис.Рік тому
3rd Session of Bushy park's Street digs in Association with B.A.D.D #streetracing #dragrace #barbados Disclaimer: I don't own copywrite to any audio or music in the clip
Cash Days 2 Recap & Preperations for Upcoming event
Переглядів 992Рік тому
B.A.D.D Cash days 2 The Rematch Recap.. prepping the car with couple new updates and changes for rescheduled event. #4g63 #dragrace #mitsubishi Sponsors - etstechcafe.com, Big boys tow and recovery, maxtorqueperformance.com Disclaimer: I dont own copywrite to any audio or music in the clip
Custom Rotated Turbo Setup on '08 Subaru Impreza STI !
Переглядів 3,4 тис.Рік тому
Custom T3 up pipe with external wastegate, mated to Garrett GTW turbo, custom 3 inch downpipe, into full 3 inch exhaust with twin dual 3 inch exhaust pipes. #subaru #ej257 #customfabrication
Cash Days 2 Best of 3 Showdown Race - Car VS Bike 1/8 Mile
Переглядів 1,1 тис.2 роки тому
B.A.D.D Cash days main event showdown, 2 best of 3 match up for the 6 second bracket win @bushyparkbarbados9326 . All owners of the recorded videos or images can feel free to comment or tag their names to receive any recognition for them. #4g63 #dragrace #mitsubishi Sponsors - etstechcafe.com, Big boys tow and recovery, maxtorqueperformance.com Disclaimer: I dont own copywrite to any audio or m...
4g63 Swapped BMW E46 Drift Car! Part 1
Переглядів 1,9 тис.2 роки тому
Bmw e46, swapped with 4g63 engine bolted to a toyota 5 speed gearbox. Engine mounts fabrication. #bmw #4g63 #driftcar Instrumentals produced by Prod. Phantasy music production
Honda Skunk 2 Ultra Intake on 4g63 Turbo Engine
Переглядів 8182 роки тому
Modding a honda skunk 2 ultra intake manifold to fit the 4g63 head.
Friday Night Drags
Переглядів 1,7 тис.2 роки тому
Bushy Park in Association with Barbados Association of Dragsters & Drifters, presents Friday night drags.. #BADD #Dragracing #Bushyparkbarbados
Main Event Showdown @ Verzuz 2 Drag Race Event
Переглядів 1,1 тис.2 роки тому
Drag Club's first event for the year. First shakedown with the AEM infinity, Shout out my sponsors, etstechcafe.com, Big Boys Wrecker Service, Maxtorqueperformance.com #etstechcafe.com #BarbadosAssociationOfDragsters^Drifters #BushyParkBarbados I don't own copywrite to the music in background
Install and Tuning AEM Infinity 508 and CD7 Dash
Переглядів 2,4 тис.2 роки тому
Install and Tuning AEM Infinity 508 and CD7 Dash
Evolution IX Dog Box Dismantle & Repair
Переглядів 9702 роки тому
Evolution IX Dog Box Dismantle & Repair
40PSI Boost x Gear on FWD Mitsubishi Mirage Coupe
Переглядів 1,6 тис.2 роки тому
40PSI Boost x Gear on FWD Mitsubishi Mirage Coupe
Evo 9 Quarter Master Hydraulic Throughout Bearing Replacement
Переглядів 1,8 тис.2 роки тому
Evo 9 Quarter Master Hydraulic Throughout Bearing Replacement
800hp AWD Mirage! First Dyno Session (Road to 800HP) Part 2
Переглядів 3,1 тис.2 роки тому
800hp AWD Mirage! First Dyno Session (Road to 800HP) Part 2
Badd Motorsport Drag Racing Verzuz Event - New setup Shakedown
Переглядів 3,8 тис.2 роки тому
Badd Motorsport Drag Racing Verzuz Event - New setup Shakedown
Evo Engine Strip and Rebuild, Turbo Upgrade, E85 startup and Tuning
Переглядів 1,8 тис.2 роки тому
Evo Engine Strip and Rebuild, Turbo Upgrade, E85 startup and Tuning
Gearbox rebuild, and Engine startup, Tubeframed Complete!
Переглядів 6493 роки тому
Gearbox rebuild, and Engine startup, Tubeframed Complete!
246-Island Auto Test and Tune Aug 2021
Переглядів 5 тис.3 роки тому
246-Island Auto Test and Tune Aug 2021
Mitsubishi Colt Front Tubeframe Drag Setup, Part 2
Переглядів 6323 роки тому
Mitsubishi Colt Front Tubeframe Drag Setup, Part 2
4EFTE Turbo Starlet Top Mount Manifold Fabrication
Переглядів 3,7 тис.3 роки тому
4EFTE Turbo Starlet Top Mount Manifold Fabrication
What axles and hubs did you use?
Did the link ecu circuit board actually locked in place like the oem circuit board does? because it looks like it didn't locked in place like the original does. I wished you had shown how the circuit board actually fitted inside the black box and if did actually sealed on the sides where the pins are. Also did you checked the base timing with the car running or did you lock the timing on 10 degrees and cranked the engine to check for the offset and then started the engine to check for the delay at 3k rpms?
Awesome my friend
Silver shim you use directly for new clutch?
Any updates to this build?
Nice job man, hope to see it back out soon.
Do you have any videos on how to set up a ecbs for rotated turbos ?
What’s the flow numbers and how do you know if you helped it or heard it you didn’t do any measuring you just started cutting. 🤔
What thickness pipe are you using
3.5mm
Hey Bro, how long did the face plated take to get done ?
About a month or so
@@SilentMan1 not bad at all, need to get my 3rd and 4th done as we....how much did it cost ?
@@khemrajhsamaroo3671 was a while ago..can't remember exactly. But I think they have the prices on their site.
Great job 👏
Awesome fabrication!!
Can u sharing if my linkg4 blink 122 max duty still can drive cause since my fuel pump weak
Thanks for the video. How much power increase do you get from this?
Has anyone done this with the Yaris?
thanks for showing this process in decent detail. been looking for something like this.💯
You will always have a boost problem because of how you have the waste gate set up on the collector, the air has to turn more than 90 degrees so it wont controll the boost well.
What did you soak the tires in? Armour all?
Where u based UK ?
Caribbean. Barbados.
🔥🔥🔥🔥🔥🔥🔥🔥🔥
You're gifted maybe more than you realise. Great work bro.
Nice job for real !! Where did you get the diy kit from ??
Where your workshop located bro?
Christ Church, not too far from the airport..
Great video, thanks for keeping it clean without swearing
What Garrett GTW turbo was used ? How much did it end up making. Curiuos i have a new in box Garrett GTw3476R and ewbating on running it or not.
Not even sure myself
Good work bro, Evo's are the real deal. Where your workshop located?
beautiful job my brother our little islands build amazing cars
Nice work man....complete sonata head and block or just head
Complete head an block.
Good job bro!!
Hey i enjoy your channel question when fitted that k24 engine into the pegueot car how you the axles to fit into the spindle of that car it's Honda axle you you because I am myself doing the same project
Thanks appreciated. The customer was actually going to send measurements to driveshaft shop and have custom axles done for it.
@@SilentMan1 are you on wats app o would like to have chat with you
Msg me on ig @silent_dcr_motorsport
"promosm" 😩
This is awesome 🔥🔥🔥🔥 those ITB’s 😎
Hey man I have this same setup but I need some assistance . Getting off 1st gear is a pain . Can I contact you ?
No prob
I’d like to hear more about this
Need to consult on a 1zzfe. What is your number.
Fuel cell is so shinnnyyyyy
What gearbox did you use ?
W50 Toyota box
looking good. what size pipe do you use for that manifold ?
1 1/4" Internal diameter
@@SilentMan1bought from where?
@@km6832 Williams metals.
@@SilentMan1 that is not what i wanted to hear. Got any experience with header tubing from redline imports?
@@km6832 haven't made any from stainless steel as yet
Proper work. Plan to 2Z swap my vitz also would love to get in contact
Great video . What's the title of the intro track you've used?
6th Sense - Let's Do It . It's Notherground Music Album
@@SilentMan1 thank you for that. Looking forward to the next video on this 👍
Good job
Where did you get those ITB’s from and how do you plan on making them work? I’m asking because I want to run them on my 2ZZ Celica
Customer supplied them, not 100% sure where he got them. But an adapter plate was made and welded to them to fit the 2zz flange.
@@SilentMan1 interesting. Cuz I know a company makes an adaptor for 4AGE ITB’s so it’ll be interesting to see how what ur doing turns out
what is the name of ur cluster u use inside the car?
Aem cd7
What a surprise hearing a Bajan Accent.
love those ITB's
Video harddd bro I like the behind the scenes vibe
The magician is back man!
🔥🔥🔥
Quality Work Dan
Great work as usual bro!
Nice