Відео

Actually not that long waiting , just panel line all of it one shoot by section, after done panel line just cleaning from the first parts that you start panel line, see lots of people is recommended using lighter fluid for cleaning because it won't have much damage to the plastic, but im using the actual tamiya panel line cleaner without any problem until now , just carefully don't use too much to clean the surface

@@estgunpla529Thank you! Just subscribed to your channel.

@@JM94_ You're Welcome 🤗

All the Markings on the armour is water decals

Yes it is , because this kind do not have proper inner frame

Hi , no ya , most of the gunpla didn’t come with water decal , have to buy separately

Hi , no ya , most of the gunpla didn’t come with water decal , have to buy separately

@@estgunpla529 oh.thx!

Around 16-18cm

@@estgunpla529 thank you very much

Hi, actually for this kit i do not apply any top coat , just apply water slide decals only 😊

Hi, So far i have few kit do not apply any top coat and also have decals on it but still fine, not a single decals come off , i think most important is if no apply top coat then better not to play with it too much, and when applying decals can use decals glue like mr.hobby decals glue (blue cap) works fine 👍

@@estgunpla529thanks for the tip. So if i were to put water slide decals on a RG unicorn the decals wouldnt come off during transformation and without top coating?

Peel off over time*

@@chuggi9592 So far my Rg unicorn decals not coming off since i do not top coat it also, just do it carefully (really carefully) when transforming and avoid scratching from the armour or finger nails, should be fine 👍

@@estgunpla529 I am probably going to apply stickers in it’s destroy mode since I already have a rg unicorn in unicorn mode so thanks a lot. I’ve been researching soo many sources saying I must top coat piece by piece for the unicorn due to the clear parts.

Most of the gunpla is not included water slide , need to brought separately

@@estgunpla529 I see. Thanks. I’m buying my first ever gunpla today. MG rx782 v3. Can’t wait to build it with the details like yours.

Good luck with the build , its a good kit and take your time 😁

Nope , for this kit I do not apply any varnish

For this kit I’m not fully painted, just hand painted the gold parts details and all the hydraulic pipes with red , then dry brush some dark silver to make look like it been to a lot of fight n scratches all over the armour. Lastly finish it will matte top coat only 😁

Actually it quite easy to do , cut out the decal and soak in water count around 10second then use a toothpick move the decal to your kit, as long as you keep drip abit of water on the decal it will still movable , give it a try 😁

@@estgunpla529 oh sweet, I might have to try it when this exact gundam delivers

@@jakeando5642 I said the same thing I was tired of my kits looking so plain so I practiced on the base of a stand an after 2 I realized they are actually easier than regular stickers because you can adjust them you gotta try it it's super easy an adds so much to your kit

Yes, i just paint some bronze colour detail on the joint and this kit itself come with two tone colour on the armour

@@estgunpla529 Wait, so you get two alternates of the armor, so essentially you always have spare parts?

@@ragingsaviorkami9862 nope , im just using 1 kit only

The waterslide Im used is from Evolution Studio (EVO)

LED not including in the box ya , lain beli

Thanks mate. Yea ,do weathering on gunpla really changed the look of it so much , waiting for your HG build soon hahaha

@@estgunpla529 yeah! I’m planning to complete the Build Diverse Re: Rise models. Haha. If only I can customize and add more details on their armors, they can look much better. 😅

@@Noobuildz that’s great , I’m still learning on how to add details on my kits , still not confident on my scribing skill haha