Відео

That’s beautiful! 😮

I'm going to guess, wires were too short so plug wasn't snapped all the way on. I've seen it before.

Had an Alliance compressor that is being replaced as I type. It will get the new Red Trane branded equivalent compressor. It's only 4 years old. The specs show it having a Climatuff but that was incorrect also. Had a 'Hard Start" kit installed 6 months ago but the compressor began buzzing like crazy and I had it swapped. (Not cheap even with warranty).

Thank you so much, sir. May Almighty God bless you. You have saved me a great deal. 👍🏿

Is the labor hard? What would u say about that. How hard is it

LG compressors are garbage

Loose connection from the factory 🫣

It’s toast 😢

The ole Canned Ham.

I can't get the thermostat to kick the condensor on, it just blows heat

Look at all that meat 😂

Perfect instructions and demonstration as I was able to increase heating blower speeds from factory default settings and not requiring a service technician. Thank you so much!

Scared the shit out of me when he said he rebuilt it at that miles 😅😂😂

why my ac termostat stops after 5-10 min of run

Tge most common mistake when installing a Honeywell Pro, is installing a Honeywell Pro. This is the worst T-Stat on the market.

Escante!

Pig tail it

Thought by code you can’t have two wire under a single screw in the breaker.

Do they realize putting that duct work above the insulated space it will be much less energy efficient?

Nice job!😮

Man, I couldn’t do it. Glad you get paid enough

Fresh off the grill 😮

LOL.

How can I get an Elbow to fit my unit. Thank u

What kind of leak detector is that?

Bad txv

I call it Game over

How do you T tap into flex like that?

Does it bubble????

I wanted to see how to build the condenser stand. Looks like I’ll have to figure it out before the crane shows up.😂

That thing doesnt work

Get yourself a megohmmeter… you can provide a lot more info than just yup its grounded… give customer actual state of the windings.

Did you check the start cap first. Pretty rusty. Maybe bulging.

I'd like to do this on our house in Phoenix. How do I contact you?

Was that a mash-up of both brazing and Stabrite? -- couldn't see for sure. I'm sure this isn't the only problem with that install.

Sorry, what was the issue?

WHAT!!!

I have a 4 ton system. Do you know where I can get a replacement motor?

the problem was that the tool was 60 bucks

Are you checking the LRA on the start winding?

Of course it's a carrier

Were you located

That maverick off of fain roaf is crazy busy during the day and evenings. It's not very busy as a truck stop though lol

Replace? That's a joke, right? It is probably grounded due to a sloppy electrical job. That thing is new. Some hvac hack thought he could do the electrical the last time. Call an electrician this time and save 10k.

HVAC companies are scams. Learn to braze, pressure test, decay test, hook up simple electrical, etc. it’s not rocket science. Installed my own furnace and ac years ago and it’s leak free doing fine. Saved thousands.

Is this really worth it? I can get a Lennox system that is 18 seer for little over 1/3 the price.

You forgot about the part where I call the salesman and he goes in and sells granny on a new 15 ton Mitsubishi city multi vrf

That's it young compressor, you are grounded! 😂

Love the video. But I see a lot of start kit videos like this, it doesn’t actually lower amps, your meter just calculates it that way. It shortens the amount of time start up takes by putting more amperage through the start up windings. Not an upgrade, never was intended to be. Hard starts or really just for old compressors that are locked up with no other options.

The really sad part is this whole installation was the brainchild of someone with a college degree.