Відео

3m makes quality products

I just bought six boxes of these. Mine stationary in the top of my toolbox I found I had to counter sink and add a third screw to each rail so that holds it down steady.

yap yap yap

Great Video my brother

They are much better than ATs but compared to mud grapplers, it’s not even comparable. And the possible damage to the Jeep is what difference tires can make via prevention. True mud tires require little or no speed - for that, I would bet by doing similar things, no lockers ad crawling up at any speed you wish. They are great in snow. Every off-roader need to try real mud tires at least once.

Any clutch work needed for 35s?

Big ass machine that can do everything better then can am plus doesn’t brake down so much. God suspension with that engine just roaring like 200 can am combine.

Still love these? In North East PA, ride WV as hell. Wondering how they do in mud, PA we have a lot of Mud and Rocks lol. Not busco deep mud but you know normal mud. Not looking to swamp the machine just want to know they do decent/good before I pull the trigger. GREAT video

They both have their good points. The nice thing about the medal one is that you can twist the sockets to line up what size the socket is. I can speak for expensive sockets but, the cheaper ones never really line up. Meaning, the stamped size and the bottom of the square hardly ever line up. And the medal one can be twisted so you don't have to waste time looking for the socket you need. The plastic ones fit tight so you can pack more sockets on one rail.

Which is EXACTLY why you dont do an early break in oil change. The break in oil needs time to finish mating all the surfaces in the engine and take out all of the imperfections on all the parts, which continue until the break in period is over. Doing an early first oil change just contaminates the new oil and prevents the motor from being properly broken in.

Hey bro how are they holding up ? And will this work with a 2.1 inch level ?

Used the Slick Offroad and foam cannon on my 1-ton dually. Not really impressed. I pre-rinsed the truck as you did, foamed it up good, let it sit, rinsed it off with the power washer....but a thin layer of grime still remained. So i had to go over it again by hand with the wash mit and a bucket of dawn and water to get the truck really clean. Don't think i'll buy this product again. Although the foam cannon is kind of cool and will keep that for general use around the farm.

Milestar say 37.8" so pretty close to what you came up with.

I do automotive for a living. Bought the Husky 52" in January and it's been great so far. Not sure if I should blame it on thin metal or "lower quality", but one thing I noticed recently is the bigger bottom drawer making contact with the welds on the very bottom of the box. I do have some weight in that drawer but it is not jam packed. I had to remove the drawer and grind off a little bit of the welds (don't remember if it was 2 or 3) so it does not make contact anymore when opening and closing the drawer

you dont run these tires at a low psi, theyre meant to drive on the center section at a higher psi 36-38. theyre a domed tire.

Just used this kit to restore the headlights on my 2006 Infiniti G35 coupe. The results were excellent. Just wish they included two Trizac sanding discs ( one for each headlight) with the kit.

I just changed the front lower control arms (with bushings and ball joints already installed) , struts, outer tie rod ends, and sway bar links on my 4th Gen Ram 1500 with 200k, I last changed shocks at 100k, and damn this time was so frustrating. The shock foot bolt was seized, and the lower control arm bolt to the frame was seized as well. Had to cut them off, but After I installed it all, I took it to get an alignment and all is well now, Rides just like new. I did the rear shocks, but now I have to do the rear springs.

Do you put the grease gun straight into the “zerk” fitting?

Thanks again to GlueTread for providing me a kit to review. They also provided me with an important note that I would love to pass on to my viewers. When grinding down areas of the tire use a lower speed method that doesn't cause high heat and smoke. This changes the effectiveness of the glue bond. I will likely explore this more in the future.

Take your front sway bar off

One thing to consider when purchasing a surface cleaner is it needs to match the gallons per minute the pump delivers, generally 1 gallon per minute delivered equals 4" of bar length for optimised cleaning, so a 20" ideally wants a 5 gallon per minute pump delivery.

Too bad they fail should have got cmi precision so much better but good luck with those

I bought the 20" it worked fabulous, however on the second use, the cheap plastic handle would no longer press the "pin" in to start the water flow. The plastic bends before pushing the pin in. very frustrating

Great video! I’m using this later today and hope to get good results, good instructions as well 👍🏼

500 miles for initial oil change is fine. New cars wait like 3k miles and no problems. This ain't the 80's anymore.

Great video, very informative. Heading to Moab and then to the Rubicon Trail and looks like I'll be disconnecting the front sway bar.

This stuff works great😂

These clips fit on the NAPA Carlyle rails example CHT SR15B should you desire colors and or different lengths..The rails are on sale now.

Thank you.

You said grease them every 3k miles? That’s high maintenance in my opinion. Did I hear this correct?

I have the 18 drawer, 72" tool chest and I love it. It has increased $400.00 since I bought it. I have a lot of Husky products and I'd buy another of their tool boxes in a heartbeat.

Thanks!!

Still going strong?

did you ever ride anywhere besides Busco. Wanting to know about that tire. I ride Busco and WV Im about 2.5 hrs from Busco

SQUEAKY LID ?????? We are becoming a society of professional complainers !!! You got a brand new beautiful tool box Bud !!!

Thanks for making the video! Using the plastic bag in the box also works well to stretch the clamp over the roll cage. Thanks for supporting a fellow UA-camr.

Someone tell him that side wounds are not fixable. LL : )

hello, Are you interested in testing products? We would like to invite you to test the Side Mirrors for your Polaris RZR

Great review! It's cool to see a sidewall repair hold, I was thinking after the first jump it may let go lol.

So I’m thinking of getting some 36.5” tires on my turbo R. Have you had any trouble with clutching or can a factory clutch handle those tires okay?

Great Review, I have the same model Rzr and I'm looking for a different trailer and new straps. What's the trailer manufacturer?

You should try the Gibson dual stainless exhaust on it love to hear the sound of it

Hola! Ese kit asi lo venden? Que medida de neumaticos usas?

Inch tires? 35?

Very good video, thanks for sharing

Hows he liking it after awhile now?

Ty j,liked it lol

Great video these we are just getting here in South Africa so your info is of great help!!

Good review ! Just bought one on Cyber Monday

4 months? I got mine in 3 days