Відео

Dang for some reason your video cut short, I’m installing one of those now and had a question? Do both white wires need power? Reason is, I want tie into one side of a coil on a Mag using power from the auto side of an HOA switch on a pump panel? I Only need one wire

Does the dealer make you do any regular maintenance with them? Can you run the A/C and the pro-power overnight while parked with lights and dash off? No sleep or Camp mode?

🔥

did it work on the Tesla?

Exactly like space heaters that work with gas. Milwaukee has made a perfect system more complicated by making a tool that also needs a battery

Good to know. 😊

Wheres the rest of video I coulndt find it

100s of licensed electricians across the USA ready right now Evchargerfast.com

I live in a old house apartment and these baseboards heaters are very expensive to run there is no insulation whatsoever in the entire building the walls feels like cold concrete all the windows are drafty no matter how much plastic you put up you will still lose heat the doors are drafty as well my electric bill was over 450 for a one bedroom I just opted out of not using them and just eventually save money to move to a better place that has insulation

The empty cell phone case tells me all I need to know.

You can get a small paint correction kit from auto zone. Comes with a small sanding pad and steps of sandpaper all the way to 5k grit to get tly buff those out in small stages. The bag will look new for 13$. I have used it on many small paint corrections, and I have no experience with paint corrections.

That ain't it aye George 😅😂😂

I got some of these JJN 200w panels and just tested them at 50 degrees in the slightly hazy10AM mid-November sun here in the NE. The first panel was 28.5V @ 8.16A and the second panel was 28.9V @ 8.17A. Rating: VOC is 28.1V and ISC is 9.12A. (To avoid a spark when testing amps, I covered the panel, connected the terminals and then removed the covering) Not bad! I'm happy with these. Now I'm going to make some PVC kick stands for semi-portable use.

I have electric baseboard heaters in my 1500 sqft house and my home is always toasty. My electric bill is never more than $350 which I think is good considering my reg electric bill without heat or ac is around $120. Say what you want about electric heat but they require almost No maintenance and are extremely reliable.

My bike has been in storage for 2 weeks now…miss it already…

Thank you for the tip Sir

evchargerfast.com/early-member-registration/

How did the mix of batterys work out?

That laugh

Hope some can tell me but can you run this off the load of your solar controller instead of the extra battery?

We are Live

Every item you shoved is overpriced. Just go to harbor freight if you want to save money.

Thanks for this review, I am looking forward to getting one. I like the idea of the rack inside roof support to limit wind drag.

Get yourself over to Gerry Palladino

Japanese bike supports free America Harley supports DEI lbgtq 🌈💩 you did good to get a Honda

Come on man it's not the bike it's the operator

I'm sure it works but you are going to burn through those motors I think. How has it held up?

No klien is garbage ive been using their products for the past 11-12 years and the quality has gone down hill not to mention they dont cover anything that breaks after 90 days i was backing out a flat head screw out of an oven outlet and the tip broke off of my 1000v flat head and they refused to replace it the handle had no wear marks no hammer strike marks on it the warranty is garbage now same goes for milwaukee so i went to lowes replaced all of my electrical tools except for my testers with kobalt they have a lifetime warranty no questions asked the store will exhange them right now no wait and they have the exact same ansi rating and approval!

Disgusting display of ignorance from a self described “idiot” I guess that’s the internet for you. I hope you win your race to the bottom.

hello - may I know the length extension of the inner rod when it is fully extend?

Buy once cry once

that one wing you saw…i think you said F68….its an F6B….

you’ve definitely done some travelling on the bike this summer !!!!

Dang!

Ok, I understand... I'm asking you because I didn't see a switch, maybe you can explain it in the video, but as you can see, not all of us are good at English, hehe... but then tell me which of the cables you have connected goes to the switch?

“That’s Electromagnetic Radiation” Yes, and so is light.

Hello, is the MC cable the one that carries the current or is it the one that goes to the switch?

"Thirty aught six"

Back in the old days there was only one size of wire, and if you needed to flow more current than the one size could handle, you just ran multiple cables in parallel. The “aught” comes from the manufactures suggestion of how many parallel cables were needed for different amperages. 150 amps or less: “1 ought to do it” 150-175 amps: “2 ought to be enough” and so on..

00 is double aught buck... typically means 0.

30-06 😂

I was told by my grandfather who was an electrican for 65 years "you awt not touch it"

This would work if y'all didn't sound so scripted. It's like watching a soap opera .

My favorite part was when he didn't actually test it. What a fucking moron.

Wtf!!! What is it with you Americans and u turns.. If your not doing them in parking lots your doing them at home!!! How many do you do in a lifetime!!! The damage youve done ..mindless damage when you have forward and reverse!!! I despair i really do Absolute comedy gold Keep em coming!!!

Quality. Price. Time. Let me keep that in mind as I am starting to do my own thing and find my own customers. Appreciate it 👌🏾

This seems like it isn’t worth it for the additional cost a lot of the time I find simply adding more panels it’s a much better approach

A couple things to consider about these comparisons is the Knipex forged strippers have a shewe cutter and the Klein you chose is a pinch cutter. The Klein heavy duty strippers with the shear cutter would be much closer comparison. Also, Knipex diagonals are rated for hardened wire also and the Klein red handle are for copper and aluminum only. The 2000 series Klein's would be a good match up with the Knipex. I do agree though, in my experience Klein cut better

Hahaha that clip is from my country, i know even the exact corner that video was taken on

you know your stuff, but the flathead, neither philips/pozi does have any insulation on its shank. you would benefit of rubber gloves.