Відео

Hi fellow. Did you know what BCI that battery is? I being looking for some battery like that where the negative post faces the side of the car.

Are all rims and tires the same size?

Nice. Did you end up getting a GR? I run 27x9x12 M1 Evils, thinking of going 28s. I do not want to get into GR, think I will regret going bigger?

The fault was a 'dry joint' .

Perfect.!

Been battling a 94 22RE. Engine was replaced not that long ago. Lately when it’s cold and I pull up to a stop, it may just die as if ignition shut off. Replaced signal coil in OEM distributor as that was bad. So with new part, cap, rotor, plugs and wires, no change. Once real warm it might not stall, though a 20 mile commute to work, it had stalled at entry gate, so that much distance should have been good. Not so old as expecting TPS to be sticky, but suppose it could be checked as well. Friend who owns a shop has spent a ton of time trying to track it down, but nothing has cured it so far.

Excelente, I own a 1993 Toyota truck, Maybe that’s the Problem, Gracias,

I had an 84 flair side with the 22r the 4 ×4 in that truck was the real deal and cheap on gas

I'll swap ya for that truck ❤️

Hello, Are you interested in testing our products? We would like to invite you to test the Rear Windshield for your Polaris General 1000 (if your car year is 2016+

check valve lash

Can you put me in contact with Erick? Or point me in the right direction? Interested in Maverick

Is the irs worth the money over the sra if all im doing is light to moderate trail riding?

Where did you get your relay? What do you look up?

That is exactly my problem. 1989 Toyota 4x4 no start / start … what a great idea . Thanks 🙏

Thank you sir for your helpful video, my father just gave me his 1990 4x4, and it was my throttle position sensor, it was off due to a missing screw, 😂👍🏼 today I had to push it on and off the ramp at the dump, solo, thought i was done. Thankx again🫡

Hi is the handle a passenger or driver one

Hi is the handle a passenger or driver one

Hi is the handle a passenger or driver one

So run a wire from positive to a switch than from switch to the small wire on the starter?

Soooo did it all work and it kicked over?

Planning to do the same thing. Who or how was this tuned? Do you have more info? Maybe a link to a thread?

Dood y skip anything in the taire down video ya skip way to much

You bypassed Ignition Switch, could that be issue? No matter, just Clever.

Are you happy with the E36 rack or do you wish you'd gone with the quicker E46/Z3 rack? Thanks.

I want to see this video shared on the realmechanics youtube channel so they can dissect what's wrong with this advice. I assume they will say something to the effect of 'This "fix" clearly shows that under normal operation the intake has more inflow of air than the computer can account for, creating a lean condition known as a ""vacuum leak"". The $.05 kludge in this video ignores the actual problem of vacuum leaks in the intake and restricts airflow to the idle valve instead. Now the total amount of air intake is reduced which compensates (kind of) for the vacuum leak.. Just fix the vacuum leak & avoid sucking spare change into your engine. Smoke generator kits work flawlessly to find vacuum leaks & are sub-$100 on amazon!

Great video, great help thank you

Is this a automatic I’m having the same issue but I have a 06/83 production 318i but I can’t seem to find a radiator that’s in stock someone please let me know of if they’ve used any other rad for it like a eBay one

I'd say that's fixed!

Thanks for the video. How Long do i need to wait for the rtv to cure before riding? It says 24 hours on the tube. But how long did you let it cure?

Thank You Vary Much😁

I DON DRIV CHEBBY GEN MOTAR I DRIV DOGE GOBLESS HOSS AHMEN BARB MAD LAZNA

hey mate im looking to do the same with my car. how did it hold up with the m10 until you swapped it out? any isssues?

Did you ever get the stalling issue fixed?

your video helped me get my top conversion done. 2 remaining issues. The bolt holding the center motor - cannot get that off?? Alan wrench stripped it. any suggestions? it seems to just turn the motor that's in the trunk (i took off the 4 little bots first). don't want to tear it up

Hi I'm doing an equal swap. and I wanted to ask you what you did about the temperature sensor. to have the temperature on the speedometer

I'm working on swapping a Lifan 250cc 4 stroke onto one. It'll have a little less HP than a YZ85, but more torque at lower RPM. It's an ambitious project with a good deal of welding, but it's going to be a blast!

Did you ran a new high pressure fuel line from tank to the filter?

Wow looks like so much fun , i will be going this april for the first time , alot of $ spent to get this trip rolling , me and wife will be going together with a small group , once i get settled in with my rig (all the accessories added) , we will be going alot i hope , great video , enjoyed

Dent guy looks shady.

Nice set up, did something very similar to a 89 325i for 900 dollars. Times have changed now in prices. 👍

Where did you source the ITB kit? …is that from an American based distributor?

Great look and vid. Love the FD!

hey man thats a beautyfull car, how did you manage to keep the stock ecu and is it better with the itbs than stock?

Makes me wanna make more videos of my Rx-7! Great job buddy!

can't go wrong with black on bronze!!

Very nice brother

Not a single shout-out...

wasting zero time on the RX7! Love it

Braaaaaapppp