Відео

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Part 4 working on the 78 Mustang II heater core replacement. Murphy stopped me. Things were going right, I broke a bolt off in the trans, broke my speedometer cable, couldn’t get glove box in, fought to put instrument panel back on brackets etc. I then realized I forgot a brace and a lot ...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Part 3 replacing the heater core in a 78 Mustang II. I finally get to swap the leaking core for a new one. It was a fight to get it back in the car and bolted in place.

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I need you help. I started a Go Fund Me to raise money to buy a lift and accessories for my garage. I would appreciate any donation you can make. Thank you. Dan

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Today in part 2 of changing the heater core in a 78 Mustang II I fight to remove the stubborn and hard to get at heater hoses. This should have been an easy and fast thing to do. Instead it took me 2 hours. Plus I had to Rant a few times…

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I have a leaking heater core in my 78 Mustang II. The car has air conditioning which makes this job much harder. In this Part 1I unbolt everything and pull the dash away to expose the heat box assembly. I hoped I could cut open up the box and replace the heater core without removing the e...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 2 working on Project Betty. I Found the problem. There are a few rust holes In the rear window trough/channel letting water drip into the trunk. Yes the CORRECT way to fix it is to remove the rear glass and fix the entire area. That isn’t going to happen. This is a quick fix to make i...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Day 1 working on Project Betty the 1976 Mercury Monarch. A backup camera is installed, rear window moldings are removed and a lot of RTV and gunk are cut and scraped out of the window channel. Soon I’ll be resealing that channel and installing the moldings. Future work includes a master c...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift I HATE when this Happens. I pulled out my heavy misc/junk drawer and it broke off the workbench. The tiny screws I used to hold the brackets on were simply too short. They pulled out of the wood. I replaced them with longer screws and added some more so it doesn’t happen again. Dan’s Mess...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Dan's Messy Garage Merch Store! dans-messy-garage.myspreadshop.com/ Day 21 working on the 63 Falcon. I undercoat inside rear wheel wells. The car goes home with the owner tomorrow morning 😁

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Dan's Messy Garage Merch Store! dans-messy-garage.myspreadshop.com/ Day 20 working on the 63 Falcon Sprint. I adjust shifter, buff paint and install all moldings. The Project is Done!

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Dan's Messy Garage Merch Store dans-messy-garage.myspreadshop.com/ I needed a 3 pin brake caliper piston tool and didn’t have one and neither did the local auto parts store. I decided to make a DIY one out of a socket. I used what I had on hand. Yes, an Impact socket would have been bette...

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Dan's Messy Garage Merch Store! dans-messy-garage.myspreadshop.com/ I take the 63 Falcon for a short test drive. I couldn’t video a lot of it but the car runs Fantastic!

Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Please check out my Go Fund Me www.gofundme.com/f/help-dan-work-safely-in-his-messy-garage-using-a-car-lift Dan's Messy Garage Merch Store! dans-messy-garage.myspreadshop.com/ Day 19 working on the 63 Falcon. The seat , scuff plates, and rear bumper are installed.