Відео

Salut,Like, how super recording. 👌

sir how to download jetson-inference

Pls tell me how to flash this board emmc. I tried with SDK manager.board not showing

i boudht 1 eagele 101 board for my project , i have a doubt. does it pre installed with jetpack and ros on eMMC (embedded MultiMediaCard) storage.

Looks appealing !!

after assembly video , how we can run and operate the car

In Raspberry PI 3B never enter in this line if recv[0] == 'Y' and recv[1] == 'Y': # 0x59 is 'Y' I dont know why... Printed recv for two times and I've got this: b'\x0e\xd0\x00E\\\xca\x0e\xd0 ' b'\x0e\xd0\xc0\x06\x04\xed\x0e\xd0 ' TF-Luna works great in Arduino Uno

tem como instalar um display lcd 1920x1080, raspberry pi 3 model b/orange pi?

the video skips step most importantly 1) how the antenna are connected, 2) how the wheels are secured finally this video seems to be an older model than what is currently shipping. The current model the camera base has been updated allowing for the camera to be adjusted up and down. Second the antenna cables are longer and attached to receiver you need to install under the heat sink.

can you use 3 lidar sensors at once

got to the end and I realied you aren't putting in a vESC or an L298. I really like this method since it makes it clear exactly what components are in there so you can make your own. If you start from a Traxxis and donkey car you might not disassemble the whole thing to find out.

This is the same kit, right?: www.aliexpress.com/item/4000007884768.html?spm=a2g0o.productlist.0.0.3aef2d4ekl76YA&algo_pvid=60f7437e-e664-405e-b916-c921c897ac9d&algo_exp_id=60f7437e-e664-405e-b916-c921c897ac9d-0

Is this the official channel of Tannatech biz website??

I have ordered a jetbot from your website a week earlier. No update regarding the Order so far. Eagerly looking forward to hearing from you.

Is it possible to measure to the decimal point?

The 5v 4A power adaptor for Jetson nano mentioned in your website is a us or eu?

Parts name and where did you get the chaisis....??

Is there a way to run this from the IDLE within the shell? I am getting an error stating Permission denied: '/dev/ttyS0'. Is there someway to release the permission to ttyS0? It does work when I am in terminal and use sudo python to run the file.

Can u make a video on how to interface the lidar

Pathetic quality. Looks nice in this video, but I had a hell of a time trying to figure out how to assemble. Screws don't go inside any hole at all on the outer black box. Except the screws for the Jetson nano, I couldn't put any screw properly. The black paint is too thick and even the screws were not of proper size as per the holes. I have asked for a return and refund. Let's see.

can you send the original code of it i am getting indentations error

Hey there, im using tfmini plus and when i try to run the code i get this error. Please help. > File "tfmini1.py", line 6 while True: ^ IndentationError: expected an indented block

wheres the code?

You didn't show the most complicated part: how to assemble and properly calibrate the steering mechanics.

could you please help me correct this error on JupyterLab basic_motion? File "<ipython-input-32-88c4ffd83ca6>", line 1 The final steering value is computed using the equation ^ SyntaxError: invalid syntax

Is case for this available on your website

This code is messed up. There are no indentations. I would save it as a .txt file if you have formatting issues so it wont be messed up for people to download. Also using the UART ports on a raspberry pi your port doesn't work

Looks like someone wasted a video making a specification sheet.

Banana pi open source single board computer, smart router,IoT ,arduino project : wiki.banana-pi.org/Main_Page