Відео

Literally the shittiest reference video I've ever seen

That Saxophone is fire. Amazing

I think this is on the special edition soundtrack to St. Elmo’s Fire, I remember it in the movie 🍿..

Great memories!

This song was on my first mixtape back in 1989 - takes you back 😍😍

George !

🤩

Such a cool mix 😍

perfect!

I'm curious about the horsepower...

Brought a tear to my eye.

This video sucks

Peripheral port is the way to go, I had a Selectmaz PP built by izzy, 205 KW rear wheels in an RX3, that thing was crazy, once you had a PP, can't go bridge again.

i'm wondering how much power this thing made

Power output? HP? TQ? Thanks.

About how much power do people average with the carb setup and a bridge port?

Call it a science experiment.

A little lighter and higher compression rotors.

...i wana drive it. what does the rx8 internals do for it?

mazdarotary(dot)net/porting.htm

Cos halfs a for pussies, Real men do it with FULL CUT Bridgeys.

franken-wankel. nice.

is a type of port for the plates of the rotary engine that leaves a bridge in between the port so that the rotor's side seal can ride on.

Basically , you drill a hole in the block of a rotary engine. and it makes for better compresion or some shit. lol

@rekevin1 no what?

@boogieboxxxbboy hahahah no

@mlgf0ursh0tt bridgeporting is making the intake port in the side housing as big as possible but they just leave a little bridge so a part on the rotor called the apex seal doesn't fall inside the intake port.

@ToySport how can i do carb swap on my gsl-se ? any help will b appreciated..

how can i do a carb swap on my gsl-se any help will b appreciated

@mlgf0ursh0tt A method of porting a wankel rotary engine that is the equivalent of a really hot cam in a standard piston engine.

Why do every one uses carb when the engine is ported? I mean can i do a bridge port without using carb and using turbo??? Im kinda new to this things

Hahaha! That starters GONE!

im going there soon and im going to try to film

why not periph?

truley sounds like a lawn mower idc if its fast it sounds like a bag full of cunts

@ToySport how much did this cost?

@mlgf0ursh0tt its portin on the intake. look it up. its pretty cool

No overtaking?

My dad also used to race here, we just watched this and it brought the memories back for him. Thanks for making this.

@mlgf0ursh0tt It is a type of port on the side plate face of the Irons that basically draws in more air into the engine. It's like a big chunk out off the Iron that is open while the rotor passes that why it gets so loud cause does not close. It's like porting a head on a piston engine it help draw in more air and you load bottom end torque...

Because it was converted to carbureted instead of fuel injected, and thus uses the ignition from an FB carbureted 12a, with the addition of stronger coils and electronic ignition boxes to process the signal.

Why a distributor?

thats at bayers lake =D i was there yesterday. i got 26 seconds =)

how about now you have it going?

Brilliant clip, especially with the onboard clips. Love it.

i thought they were priming it?

Nope!./

me also!

ohh, sorry!! cause theres a speedshop in Quebec thats called TRAC racing!! my bad!! Joe at RPM Motorsport is incredible !! ill probably send my engine there to get a aggressive streetport.

Our rotary was built by RPM Motorsports in Kitchener, Ontario. We had been getting some support for our racing from TRAC for a while, and also, our series is called "TRAC Tour (The Road-Racers of Atlantic Canada". We are located in Nova Scotia.