Відео

@@goldtrafo2478 no the server stop

Idk why, but you look so indian

Yes pls, i needed ittttt

@THE_WORXT_YOUTEBER whats your name then

naka 0 na volume ko may noise pa dn

@@PakdeBon you can download at duino.com site

Arduino just H/S very low. Esp32 its better very high speed kh/s. but to perfect its Raspberry MH/S.

@@LaRRyl33t very bad for profit but good enough as hobby project😊

Better Speed dude esp 32 than 8266

but esp 8266 is cheaper than uno somehow...

Or just buy a GPU and use it for mining... You can buy even a cheaper one. A 1060 RTX shoud get you at least 1M power.

​@@andyandrew2453 Bruhhh that does not exist😂😂😂😂

@SuperCachoTutorialesyGameplays I mean, GPU rigs exist... But for Duino Coin is a bit too much of an bother...

tingnan mo yung pin sa board at hanapin mo yung power GND which means ground connect mo yan lahat para isang connection lng at next hanapin mo ang label na 3.3v yan naman ngayon ang positive voltage mo connect mo din lahat ng para maging isang connection lng after that i hook up mo ang power sa isang board at lahat ng iba pang board mo at magkakasupply rin ng power

just connect all pin 1 for 3.3v supply and pin 2 for ground from one board to another board after that use only 1 board to supply power to all of the other boards

you can also search image of esp8266 board pin config just to make sure that your hooking up to the right pins.

those caps has nothing to do with what happen to your potentiometer, since those were just provided to prevent false triggering of logic signals.check your potentio is if not broken or busted and look for broken or shorted pcb traces

@@nelberttvofficial the value is fine,but it stopped working,i don't know why,and the flickering display is still there even after removing those caps,so now im confused what must be the actual problem.

Not really it's still running

yes

I replaced 3 pots but still flickering. After removed all caps, no more flickering 👍👍

it was soldered using 2 pins bend and attached to the perfortrated board

@@nelberttvofficial so can i use the pins with that pins connector which we can connect the pins connector

@@riderpardhu you only need the pin with 3.3v and gnd connected to other boards pin 3.3v and gnd. make sure not to short those

3.3v is from positive side of the power supply and gnd is ground or negative part of your power supply.if done correctly, u will only need 1 cable to power all boards

check the fuse if its shorted,the also the input plug which also act as a switch...then make some voltage check on the main power capacitor,make sure theres voltage, if not then maybe a short on power supply circuit is present.

its a project not a scam😊

Sir how much po pagawa flickering display

I exactly did that and my flickering problem was solved..thanks for your update 👍

Yes, i did this way too, remove c25 and c56. And finaly, no more flickering! Thank you so much!

yes that will do

yes it will have some effect but not that much since those caps are to make sure to filter surge and noise on the power

very little, this is just for fun project

yes, like how much? i would like to know. thx

check you effects chain,there might be some kind of effects or compressor engage.if none, examine the sound quality if its clear or somehow distorted...

check your signal chain,its your amplifier reacting to the improper gain levels.the sound is being pickup up by your guitar and going back to the speaker of your guitar amplifier

proper EQ is needed to prevent feedback both from the amp and the effects chain.

Need ba tapusin ang 15 ds at 3 person tsaka maka withdraw sa games apps na ito. Thanks po

medjo nag change na sila ng rules kasi madami na nakaka cash out.medjo makailang ulit mu gawin ang 15days,10,at 5 saka invite ng 3 friends.medjo matagal na maka cash out pero okey p nman ang gold coins cash out...mabilis at walang sablay

just follow same procedure and that will be fix my friend.

naa ko sa damosa lanang naga work

check for under valued components. or check your power supply voltage,it could be running under lower voltage than whats needed by the chips.

@@nelberttvofficiali dont understand what under valued components means , i tried new batteries and pluged in different electricity plug sockets the same problem the leds are not lit at all and when i turn the parameter knobs it just appear a part of the digits only,i am sorry for bothering you i just need to fix it

@@nelberttvofficial thank you

in that case, i think there are components on the board that are not working normally,or not having voltage, its hard to figure out cause you have to do a voltage checking one by one on each chip to trace which one is not functional...sometimes this problem are often cause by faulty on board voltage dividers or regulators.

Thanks alot bro I ll try again what you told me thanks for your reply wish you all the best, peace

sorry i didnt understand what you mean