Відео

@IROCZman15 thank you man, it was a great rental. Just time to bite the bullet and go faster, safer

@MarioLT4 it's literally on my vid titled 9.90. that was last year. rental the 25th hoping for 9.70

@@tubbytownsend that's fast

@somebodyyouusetoknow4532 it's a turbo 400 and has a fti 89-0 sst 9". it needs a restall though, needs a hair tighter up top

these were Hedman 1-3/4 longtubes for a 70 nova 350

78n/54f and spun basically all of 2nd and into 3rd. Just starting to hit it good. changing to a 82n tomorrow

custom Lloyd Elliott solid roller

stock throttle body? probably a vacuum leak

@tubbytownsend I have looked everywhere. I had to send off my asm throttle body for repair. Put the stock, one back on idles like absolute crap

@jarmaljackson probably because the as&m was setup and adjusted for the motor. the stock tb probably doesnt have a large enough bleed hole or possible vac leak around the shaft, or the iac is wonky

@tubbytownsend I appreciate the reply. I will look it over again. And replace the iac. I got it from oreilys stuff is usually junk smh.

@jarmaljackson u have scan 9495 or eehack? if so do a iac reset and see if it calms down.

no, not anymore. holley terminator x max with efi connection 24x setup. was having spark blowout issues with the opti above 6k rpm

@@tubbytownsend excellent.

more like hot air intake lol

ellwein engines 385 with LE ported Trickflow 21 degree heads

huh?

its a utter shitbox lol literally. but mechanically its pretty decent. new door and spoiler then paint

@@tubbytownsend lmao sounds like 90s cars still ive always liked the sn95 stangs

thank you, bit too loud and raspy in my own opinion (compared to the magnaflow muffler that came with the mufflex exhaust) but it does sound nasty

solid roller camshaft pimpette

@@tubbytownsend lol this one made me chuckle

😂🤷‍♂️……then make a video of it doing a burnout! All I know is she’s badass

@@eastwood8646 there are vids of it doing burnouts on my channel lol

@@tubbytownsend cool man…..ima check yunz out & you got a new sub! Crazy how many dudes with badass cars are assholes on YT! 💪🚗

my other vids its same setup just obd1

its getting there, a few tune revisions deep now

109lsa

its a edelbrock vic efi sbc intake, my heads are redrilled for sbc intake pattern. thats a very very custom elbow to use a stock throttle body. unless youre spinning past 6700ish rpm and using more than 200hp of nitrous, a ported lt1 intake will be fine

a very large Lloyd Elliott solid roller. Gen 2 LT1's are alive and well

hog crankd pants shidd

literally a spare used parts build (except valvetrain). stock rebuilt bottom end LT1 with good bearings/rings from my T56 car i parted a few years back, LE custom cam for a small nitrous shot, LE ported afr 195's that we had laying around, carb and distributor. just a crusty looking g body that should go decently into the 11's/high 10's.

warren county, messaged you on the gram. thank you

2

​@@tubbytownsendwhere ya get it from and what lifters you using? They link bar? I wanna go solid roller. Sounds good af man!

@@joefein9469 uh, it was the original block built. crower cutaway severe duty link bars

@@joefein9469 watch my newer videos with the new cam. sounds much better

стало тише, чем было🤣

the green firebird in my videos is the one i emailed brad about a muffler for, thank you!!