Відео

its not working...please help

What’s the values of resistors around the (7-segments display)?

10 micro farad or 100micro farad?

Bro help it is not working it is showing 2 regardless of the operation of the switch

Please mention voltage ratings of all the components

Bro please help me its not working

Taylor Jennifer Rodriguez George Martinez Scott

Please Tell me the capacitor value!

Please 🙏 @electrooxe9623 Need help on this project. Electronic dice using flipflop and seven segment display

Hey bro ! I have a doubt..... How the numbers restricted till 0-6 alone ? Explain

Sir can you put apparatus with how many needed list in this comment?

Dear Mr. I feel very bed when some of the youtubers play music and move cursor only keeping their lips close. We are not here to listen music but to learn things which you are going to explain. Please stop this habit(bad) and speak what steps you are following. You will not be happy with such type of comments. Its very confusing.

❤❤❤

Detailed explanation . You don't speak in the video but your video speaks... 😎😎 Waiting for more... 🎉🎉

Crazy dude, this tutor is far more effective than any tutors I’ve seen on yt, thank you so much

may I ask the value of the trimpot?

buddy 3;12 pe kya laga rahe hoo ?

Bhai tui valo na

Can I use 4033BE IC

Can I use 4033BE IC

Can I use 4033BE IC

How to make it work on Internet

koi solution bta dy

bhai ya kam nai kara ha

Camera probe failed with error 0x105 how to slove the broblem bro

disculpa no se puede hacer un contador del 1 al 9 con el 4047 y el 4017 y el 555? es que estoy probando y no me cuenta bien 😢

I want to take photos with the button. What should I do for it. So I want it to take the photo with the button and send it to telegram.

Great work, keep them coming

how to connect additional two 7-segment display?

Sir can i use 4017 ic

You should connect resistors at each LED based on your voltage, forward voltage and forward current. Also, I think 6 is not lookink properly😅

Ano po yung may code na (key 1 k4-6 x6_th) sa diagram na may 4 pins?

at the end of the video you have changed all the connections that have been given to the bread board

I used 9V battery but the display doesn't get on why?

Hello! Thank's for this amazing video and code! For a scoolproject im trying to code it by my selfe, with your code as basement. And i'm stuck here.. : Can you explain my why you use these large numbers in Arry(active)? (131072,65536....) I really appriciate your answer, Thanks :) switch(figura) { case 1: //"O" active[3] = 131072 + 65536; active[4] = 131072 + 65536; fromLeft = 3; fromRight = 3; break; case 2: //"L" active[3] = 262144 + 131072 + 65536; active[4] = 65536; fromLeft = 3; fromRight = 3; break;

I tried to do this, but only the letter 'g' lights up on the seven-segment display. How to fix this?

Value for resistor?

what pins of NE555 are the potentiometer and ceramic cap connected

Help not working!!!

did you used ir sensor or you are counting by a push button? And tell about the power supply too. did you used a transformer?

How much voltage u gave

when i try to include library it shows following error : Error: 13 INTERNAL: Library install failed: moving extracted archive to destination dir: library not valid

sir can you provide the names of libraries that are included

Love your work, I did this project. Problem is it's not counting 🥺 I rechecked everything connections I had. Do you think it's the LDR that's defective?

Hello, this video is so helpfull for me, thank's so much! Can you send me this code, link under the describe is error

You not declare pin mode 2 in code?

ye blue colour ka kya lagaya

Hlo bro iam getting "connection to telegram failed" and "LEDC is not Initialised" Please help me in solving in this I have project submission upto tomorrow evening

can you explain for me the operating principle please

Source code please?