Відео

What if you want to put a normal wheel on free axle frame can you

😅😅😅😅

He looks like he’s the third Paul brother.

Great review, where can I pick up one and how much??

I have a similar looking issue with my 2x SRAM rival axs....do you know if there is a fix for that rear derailleur also?

Just want to say thank you to everyone there @ Team Cycles. Ordered with Dan and picked my Carbon PL last week with Rich. Great experience and hand over. I've swapped out the wheels for Zipp Moto with Big Betty and Magic Mary. Xx AXS T type transmission and AXS reverb dropper along with sram ultimate code stealth brakes and Hs2 Rotors. One up carbon bars, Hope stem and pedals with the Ergon grips and saddle. Painstakingly fitted an Invis full protection kit to the frame and forks. Upgraded the forks with the bleed off valves and fitted the Fox full front mudguard for the nasty weather. Will send over some pics, it's a killer build now. Good luck with the sales of these, I'm sure you'll be sold out in no time. Great bike and service 👌👍

💯🔥🔥🔥

Можете податок зробити і відправити на Україну

Not all bikes use the 21t (red) gear as the setup cog. For example my sb160 uses the 24t cog

Это намного приятнее чем собирать дешёвые велосипеды

Dji motor, i want it sooo bad.

Ale fajnie tak sobie rozpakowywać i skladać rower za rowerem 😢

literally the most premium bike ever 👌

I am the only one to watch plz give me because my parent can't afford

Can u give it me for free

Holy shit dji dose e bikes now 😲😲

And don't forget to tighten the axle back up 😬

Ready for sheredy 👌👍💯

Dope

عالی❤

size 485? 510?

Hi, i have a question, do you need to conect the Trainer to the Wi fi to used? Or is enough to conect the garmin with the trainer. I want to buy on but i don't have Internet connection in the basement. 😅😅 Thx a lot

Bruh

Now do a video on how to remove that dorkdisc 😂

Hope the radiator is switched off! 🥵😂

😊

Great review Liam, would love to see a review on the Gen 8 (definitely the sexy white & gold frame 😜) and your opinion on the evolution from Gen 6, 7 and 8. The ‘slimming down’ of the gen 8 and moving towards a genuine do it all bike intrigues me.

even though the white line is no longer aligned after doing this tension adjustment, following this tip fixed all my shifting issues with gears 8-12

Easy does it however mine continues to fail on trail. Everything torqued to spec. SRAM sending me new mech as we speak. Better solve it. Super bummed.

👏

Wouldn't this be detected by youtube as reuse content?

Hand pump always 👏

👏

Big love to this fella. ❤

Satisfying

Great advice

Big up team cycles, Ben chapman and trek boones

Ben sent me to check your channel out

Team cycles, plz start a branch in Canada

I use my gravel bike to commute.. so scared to use it on heavy and muddy paths. I am worried it would wreck the bike.

If only they was a cross videos from here to Ben and wise versa We all know team cycles from Ben

Hopefully I’ll be visiting soon when I *praying* win this bike 🥹

Should have meet up

Unfortunately, not every caliper perfectly stays still/centered, and you might have to manually adjust the caliper by laying a piece of paper on the ground to more easily see the spacing of the pads. You loosen the caliper just enough to make small adjustments and tighten them all the when satisfied with the position. If tightening shifts the position, make your adjustments slightly off center in the opposite way of the shifting so that tightening the bolts puts them in the final position. This is more tedious, so the method in the video is definitely worth a shot for the first attempt 😅

would that work with cable disc brakes?

Ohh this is 👍🏽

Nee budget for parking like.

Love this! So that’s where my Llama cup went! 😂

Cool i would like to See more ! Have you more Cipollini 's???

I would have went with DA mech over Ultegra Di2. And how many spacers does it take to make the frame fit? 50 mm under the stem plus 40 mm for the stem is 10-20 mm over what I would consider safe...