Відео

5 years into the future you can find a video on UA-cam of a fellow pulling a dent like this out of the side of his truck bed, using only a claw hammer and hot glue. He hot glued the handle end of the hammer to the dent with hot glue, and once it cooled, he gave it a yank and the dent came out on the 1st try. Worked a lot better than this puller. Also 5 years into the future, Amazon sells amazing, cheap, paintless dent repair (PDR) kits that should work 1000x better than this puller. You gave it a great go at it, and I have looked at this kit at HF before I bought the PDR one from Amazon. Oh there are 1000's of PDR videos now that will show you have to do it the right way now. Just search PDR on UA-cam and be amazed!

Lmao

The Marge Simpson growl😂😂😂😂

It's a cheap tool, but you definitely didn't use it correctly. The surface needs to be prepped correctly, and you need the puller to be on a flatter surface. That puller is not compatible with the location of your dent, and you need an oval shaped attachment.

What a ridiculous video. You got a used thing and decided to make a video on how "bad" it works to "test" it. All you had to do was exchange the thing for a new one, and you could have actually made a somewhat useful video, but no, you had to make some bs clickbait instead. What a complete waste of time.

I bought two Brio battery engine sets for my kids for Christmas. I wanted to install the batteries before wrapping them and ran into this issue. Thank you so much for your help. There will be two very happy kids on Christmas morning thanks to you.

Cheap glue😢

First you didnt used the heat gun to shot at it first. Wrong way tho

Why even post this???

10 out of 10 for perseverance you had me in stiches

**FUNNIEST SHIT IVE EVER WATCHED**

Dent looked better

I am pretty sure it tells you not to press the tab into the glue

What a doofus.

Adding heat to the area with heat gun makes all the difference . And start on the outside and work in.. slowly

Great review. Thanks

Total fail😂😂

You should have poured boiling hot water on there first. It works better when do as the hot water makes aluminum/metal surfaces a lot more flexible.

Use rubbing alcohol to release the hard glue.

Sounds great. Dont listen to haters. Good job.

For one thing, you waited way to long to put the puller on the glue.!!! Prep everything first. When putting the puller in the glue, press it on to the car for about 20 second ish.

Do not do what you are doing.!!!

Made in China No wonder it sucks

almost got it. if he had more information it could have come out pretty good. also, did better than I expected based on his confidence level at the start of the video. keep trying Matt, thanks for posting.

Can not get off the floor for laughing . Is this for real .. class !

This video is so frustrating and funny at the same time 🤣 u know u can just pull it with hand after u use the glue instead of the bar right

Stupid ......

I'm lost ca t stop laughing 😂 😂 😂 😂 😂 😂 is this a joke or is it possible that this man is silly as he gets on to be

You do have to clean the release agent off unless you use alcohol which evaporates away! It might also help to watch videos by those who know what they are doing.

Lesson worth watching.

Lmao if this don't work nothing will 🤣 Take that crap back and bring that car to me. I'll fix it. EDIT: And shoot them damn birds 🐦

Gosh the agony….

Yeah, I think something like that would have to be heated a bit with a heat gun and then with a cheap tool like that you cant because it uses heat glue instead of chemical one. Then you would have to start at edges and work yourself toward the middle of the dent. I've seen bigger dents pulled but not with a toy puller and no skill whatsoever. You have to watch some videos first if youve never done it.

I'm assuming the directions didn't say this, but It does help a lot if you heat the metal first with a something like a little propane torch. Even a kettle of water hot off the boil will do in a pinch.

😁😂🤣

You should wear gloves.

Can you even put on your shoes without two attempts? You seem pretty incompetent.

buy this product with the same result, it is a waste of time with these products

More wasted dollars going to China for their junk

this is not going to work on such a hard crown. and you have been applying pressure on the wrong spot all the time :D

This guy is quite a bloak...why would someone purchase a used product and have to wrestle with a cheap glue gun... he's in the wrong business...what strange human being....hmmmm

Don’t give up, you may have saved a professional dent puller an hour or two of work saving you some money when he does the job for you

If used, return it.

i wanted to make it through this video but at the 8 min mark i couldn't watch anymore, watching people try to do stuff they don't understand how to do makes me crazy, that dent could have been pulled so easy if he would have released the pressure on it first in fact releasing the stress on the dent probably would have popped most of it out without even doing the glue pull but because he pulled the center of the dent with the stress still around the edges he stretched the metal which is why after he pull the dent out some when he pushed on it the dent sunk back in, it's called the oil can effect......

This guy doing the demonstration has the mechanical skills of a clam.

You really dont need to get the glue off the tab everytime.

i dont know what was more hopeless , the tool or the tool doing the demonstation ?

I would of just bought a new car

😂😂😂😂he said we made a dent in the dent omg I can’t stop laughing 😂

Someone used alcohol to get glue off.