Відео

Rockstar Tactical or MCS has it.

I would pass on the Super Bolt. It didnt deliver anything the factory setup didnt already provide.

@lesslethalfordummies Thank you for your honest input! I'm still debating whether to get the TMC defender or the 468 defender, I can't decide

@@ricardlubin3175my 468 is supposed to arrive today 😁

@@lesslethalfordummies I will definitely will be waiting for that video before making a decision!!! I've been told that the TMC was an excellent option and easy to use. On the other hand I've been told that the 468 is a better built, more powerful and reliable.

We shall see!

Ooof! 🥜 🤣

The tuning barrel set will be short of sticking out the end which might make it difficult to screw that second extension on but would work just fine.

Thank you for your help so I got my tuning barrel from home defence it come with the power kit it's got a little bit that come out of the gun that will still work with the carbine kit

Yes with just the short tuning barrel in the launcher it will fit the carbine kit without any modifications but you do still have to remove the fake barrel that comes installed in the carbine. Now if you want to run an extension on the carbine only then you will have make the pass through hole in the carbine larger. Someone here in the comments heat up the fake barrel and pushed it through like my socket idea and it worked much better.

Thank you very much ☺️ I think I get it now 😀 so it will fit the carbine kit with my little tuning barrel on my gun thank you 😊

So far so good and now no need to get ripped off buying “orings”.

It was just by design. Magneticc detents will solve that issue.

@lesslethalfordummies it just seems to scratch the SMG itch.... And I have multiple handguns and a shotgun already, so swap to mag detents is easy at least.

Was it that obvious?

@lesslethalfordummies not that bad. Im just being sarcastic 😄. I had to look for it and zoom in on my phone to see it more clearly 😅

Before my channel was a thing yes. For $100 it is a fun revolver and thats about it.

​​​@@lesslethalfordummiesIm thinking about one for milsim events so the 7.5j power isn't a negative tbh. Though I'm intruiged by the high power valve. If yiu want to sell it let me know ;) given they are SUPRISINGLY HARD to find in the US. Also... For. Your o ring issues maybe try vitron iv found it to be resistant to oil and cold and a standard upgrade for co2 airsoft guns especially in high stress and low temp stuff.

@@jediknight1294 the Roscoe is long gone for me. From my research when I purchased it paintballers weren’t having much luck with it shooting balls, but rather FSR which has become a bit of rarity in the 50cal size these days. A few years ago it was over $200.

@lesslethalfordummies yeah iv heard it chops balls fairly heavily. The advantage for Me is we are using it shooting foam balls or plastic 'indoor paintballs' for the most part. It's one of the things I got into the less lethal side via, using them. For training and milsim stuff. And given I'm Running a ww2 event in the next few years... Seemed a logical. Choice

I am just swapping my other M17 over at the moment 🙂

Got any questions just ask. 🇨🇦

This was my very first M17. It doesn’t get all the good stuff. More like it gets an ass whoopin.

For now i will just continue to beat on this new oring and see what happens in the long run.

Launchers love oil. There is such a thing as too much but not in this case. Some markers crave oil to prevent spitting orings at LL pressures.

@@lesslethalfordummies OK did not know that oil oil oil got it thanks

@@smokingunclefrank6037since i dont rebuild these using grease like the factory i oil every cartridge or tank no matter what. It has proved worthwhile as my failures have been greatly reduced. Now if oil is spray out the barrel thats definitely too much.

Yes it is.

What about the heatcore orings that home defense 24 sells for the valken m17

Never tried them.

The Byrna Kinetics were one of the top performing projectiles in the TMC. Their lightweight bodes well when used in a blow back launcher.

@@lesslethalfordummies Good to know I wasn't getting great power with Byrna Kinetics so maybe I'll bump it a little after some other tests

@@smokingunclefrank6037due to the narrow passages in the TMC its best result are using co2. If you are going to use HPA i suggest 1100psi. It will eat it up all day long. 800psi you will be very disappointed when comparing it to co2.

I moved its location specifically for co2 use.

My Gmags became brittle and have started to fall apart. They are just a flat out crappy design. I may still move the air out back if i can shortened it up a little.

Difference is colour and that nifty slide check the Byrna gets which is a pretty cool feature.

I will. Its quite easy and reversible. Nothing permanent. I wanted to do one less video with some nerf rockets before i show what i did. Ill admit my launcher charged to 500 bone stock and is more than enough to launch balls for the dog or knock someone on their ass.

@@lesslethalfordummies I'm reminded of an entry our team did a while back, and a dirt bag said, "Shoot me. I dare you." 🤣

@@AustinTaylor-b1owon’t find me on the business end. How did that work out for him? 😂

@@lesslethalfordummies As I recall, he took a double-tap, center chest w/riot balls and folded like a cloth napkin. With this, I'm picturing more of a dirt bag shaped hole in the sheetrock like in old school cartoons.

🤦🏽

You are welcome. Was it you that posted in the FB group with the cracked receiver?

@lesslethalfordummies Yes indeed! I was able to get MCS to sell me just a new upper for a decent price, so it should be up and running again soon. 👍

Excellent news! What kind of projectiles were you shooting?

Just aluminum balls.​@@lesslethalfordummies