Відео

Do you have the boot files for a M32?

What paste did you use?

🎉

Hey Thanks Rich very Good vid

proponują zaopatrzyć się w tester kondensatorów jest nie drogi natomiast mierzenie miernikiem nic nie wnosi do prawidłowego pomiaru w kondensatorach jest ważny stopień zużycia w % i ESR czym wyżej to jest kondensator do wymiany pozdrawiam miłego dnia

Greetings from Colombia master, I have the same problem with an x32 core, I wrote to you by email, I'll stay tuned. subscribed

Superglue with baking soda?

Wow, great video. Thanks meh brother.

Hi I reached out for the image file. Can you check your mail?

Is that the QFN package for the LAN8720A? It is difficult to see.

Everything show up but can't touch any buttons

Ebay

Hi, I send a mail to you, thankyou in advace!

hi! my name is pablo, i'm from Argentina. i emailed you yesterday about this files.

Good morning Rich! I came across your video, as I’m experiencing issues with my x32. I believe it’s the USB component. Where do you find the individual components?

Hey Rich - great videos! Thank you so much! Do you have a recommendation for sourcing Behringer X32 parts?

I have one same like this. Thanks

Where did you purchase the chip and which one did you get? There seem to be different options between tape and reel, tray.

What caused the drier to get clogged? I fix cars and if the drier on a car goes bad (clogged) it's because the compressor is going bad and pushed trash into it.

What's the purpose of this SD card? I'm guessing it's different from the dn32 dual SD port?

Great video!! Really helpful disassembling x32 producer. I sent a mail for requesting your help with my x 32 producer.

Where did you source the daughterboard from, please? Thanks.

Same thing happened to me. I also bought the new timer. How do I know which is the correct knob?

My berhinger x32 compact has no lights at all. It has 120 volts inside the case but does not show any signs of life

Why? Do you mean its recommended take of power before taking of ethernet connector?

I fully expected the SMPS (power supply) to be bad. Nice fix. (what the hell is with the rust on the bottom right side of the chassis? Was the chassis made with recycled Ford Pinto or Hyundai Pony metal?)

Can you compare the pre amps? That is the difference people are saying between the 2.

I was told years ago Midas parts are stronger

Thanks for the great video. QUESTION? My brand new X32 Producer, the number 3 and 4 lights blink on and off on the assign buttons. What's up with that. I've done a factory reset, made no difference.

where do you get the mcu? i need to replace mine but I cannot find one anywhere

Hey Rich, Thanks for sharing your knowledge with us. I was wondering how long I should keep the heat gun on the chip - I do have a laser thermometer I can use to monitor temperature of the chip.

A very helpful tip to extend the life of the compressor is to add 50ml of sulphuric acid to the compressor before regassing

One of aes50 inputs is not syncing what can i do

Where can I find the different versions?

Just had the exact same issue with one of my SD8 stageboxes. I noticed that 5 volt rail fluctuates between 1.2, 4.2, 4.8 and 5.1 volts. Which rang a bell to me as the 5 volts output comes from a variable regulator, the problem here is a very small 4k7 resistor in the corner of the board (close to the mountinghole for the screws), that is (supposed to be) connected to the groundplane, but the sheer size of the copperplane it is not properly soldered there, and therefore putting to regulator to 1.2 volts (it lowest setting). Long story short, search for that 4k7 resistor. Hope it helps somebody

Hey Rich thanks for the great work of doing this kind of tutorials. Am using x32 producer and I had to buy digitstage box sd16 i think someone had forgotten it on and burned but it in powers on but no signal light indicates orange, on x32 producer it only indicates power instead of reading so I kept it ,How can I be helped it's along suffering of having less channels ,what could be a problem and do I go about it?

Hi Rich, excellent video. I sent you an email with a video of my x32 and the failure it presents. I hope you can help me or give me some idea of ​​the error I might have.

I need that sealing kit

Expect to find issues if you continue to use just plain old CAT5 cable -- the warnings are on the ports for a reason. Worst case -- you will blow your ports on the X32 and / or the stage box. Should be screened shells end to end that you use

I send mail to you

That spider arm metal looks like it's no better than the die-cast metal used for matchbox and hot wheels cars.

Very helpful I didn’t know this existed! You may have just saved my fridge and $1200’s 😅😍❤️

please tell me, we also replaced the faulty capacitor, it still doesn’t turn on, what could it be, I would be very grateful, do you have a diagram?

gracias tenia un problema con sonido... gracias a este video pude verificar la linea de alimentacion de la fuente me falla la de 5 volts

sos un capo...... saludos desde bolivia

Great video. What PSI do you pressurize the refrigerator to find the leak?

Hello. For a working X32, is it possible to put a blank sd card into the slot, and boot with a firmware in the USB slot ? Would that make a working sd card ?

Hi Rich. Do you know the part number for the usb port were you put your usb flash drive in to update the frimwear? my usb port do not work and i cant update the frimwear without finding a new usb port? Hope you can help

Hi Rich. I have the exactly same model and problem. I live in Canada, how much should that service cost please? I got absurd numbers that makes sense to buy a new one. Would you please kindly share this information, so I won’t get ripped off. PLEASE AND THANKS

Our 10 years old X32 suddenly started producing heavy sound like a machine gun on all output channels. Only way to stop it was to turn off the power. Turning on again gave the same result again. Now, a week later, I've turned it on again without the problem. It still seems to work OK after hours on. Based on your experience, can you point to a reasonable explanation, and point at which card would need to be replaced? Ole