Відео

I have a 928 that I bought in 1993. Not a typo! Have made the normal repairs, belts, a few cables etc. Lives outside with the honda cover. In Montreal winters - still starts on 1 or 2 pulls. You will be very happy!

Wow I can't thank you enough for this vidio, I am very new to the hobby I purchased a Capra 1.9 and then ordered $2,000 + in part's including the FlySky GT5 , I went with the fusion se 1800kv instead, but the explanation of the radio was great. you gained a Subscriber

Hey, thanks for the video. I found it very useful. Can you tell me what bolt and washer kit that was at 13:38? Where can I get that? Thanks!

Isn't the program card a waste of money , the gt5 allows you to set all of that ?

How was you drive shaft clearance?

How about using it?? Works good sitting on the ground!

When your power down your capra does the motor "jump" for yours?

I ABSOLUTELY Love ❤️ my Hamilton Beach flex speed coffee grinder. Does a phenomenal job!.

I bought a 5 gallon beer Carboy and separate the ethanol and water out and run ethanol free with stabilizer

Installed this motor yesterday. I know everyone says it but gah the low end torque is ridiculous. I'd buy it again and again.

Was it a clanking, like steel on steel? Or just the wobbling like you said. I can't figure mine out. Definitely better with snow in it. Everything is tight. I mean I'm thinking I bent something. Auger looks like it spins level, balanced.. & so does impeller

Appreciate the advice

Aha, I had the same breakage when I shaved down the link mount when I dropped in the Hobbywing Fusion SE. Weakened the crap out of the connection point and it broke on a bad fall. I replaced it with a PETG 3d printed skid (where I was forced to remove the dig servo) and then _that_ broke when I got into a bind. Finally gave up on all the hackery and went with the Vader skid as well - should get here on Wednesday. Plus I can put my dig servo back in! Looking forward to the upgrade.

Nice these look good!! Wonder compared to your cool Capra

Subbed and liked!! When I did my skid n my sporty Capra build and it didn’t work. Move up link mount on chassis side. Those skids do suck. Can’t beat the fusion!

Correction! The sheer pins are not there to protect the auger blades from bending but are there to protect the auger transmission brass worm gear. Also Do not go bigger or smaller on the sheer pins. Replace with OEM and replace both of them. Don’t forget to grease the auger shafts! If the auger rusts to the shaft the shear pins are non functional and you will destroy the brass worm gear. One last thing! Pull the wheels and anti-Seize the axle shafts every season! If the wheel hubs rust to the axle the only thing that you’re able to replace are the belts! 😀

Great video

Great video I have subbed to your channel 👍👍

I've had this thing 10 years and just discovered that you can adjust the tension pulley... Problem I'm having now is the impeller shaft/pulley moves a lot and contacts the tensioner pulley arm and sparks. I can't figure out how to fix the slop

its good to have a reference for how far that external lever that connects to the cable should move - not much at all. thanks!

Nice

Can you confirm on how many gallons your fuel tank is on your generator Harbor Freight is stating that this is a 8 gallon tank on this generator but I believe it's more of a 7 gallon or maybe even a 6 but not an eight because I'm looking for a replacement tank for mine and all I see is 6 and 7 gallon tanks not 8 gallon so I think it was a marketing a sales pitch does the advertised on the box that it was a 8 gallon

its made of Delrin.

Great review, I have a cub cadet that attaches to my tractor. It’s a belt drive, I live in the Buffalo area. The Cub blower is junk, belt slips and burns. I think this is the tank for me! Thanks!!

Really liking your videos you don't need to apologize for the length some people like long videos!

Fun little video thx

How do you feel about the 928 now? I'm considering one now ,thanks!

I’m currently upgrading my Capra I have it taken apart & have the Vader skid ready to install I have the Fusion to install so I went with the Vader skid to get it in correctly. This seems like it’s going to be a great upgrade. I’ve had my Capra for quite along time but have not done anything to it other then a Reefs front servo & metal beadlocks so it was tie to update it. I have 2.2 wheels & tires overdrive gears & 90 mm Desert Lizard shocks.

Ruptures on my Redcat Ascent & my Capra 4wheel steer.

Nice video I got the HSS724CT I think yours is a bit more advanced but you got to love the Honda

Cool vid

What an awesome video as usual explaining everything in fine detail. Very much looking forward to seeing her in action

😝 'promosm'

Nice well detailed video brother !! Looking forward to seeing it and operating it in person

Running into the same issue with my Capra build. I shaved the Treal skid link mount down to the point where the motor sort of fit, and it’s a bit thin for my liking. I was between the Vader and the Rock Pirates skid, I ended up going RP so I can run an SCX10 style trans. Great video explaining this!

A great in depth video brother !! Love how the looks of the new portals !

How much did you pay??

Looking forward to seeing this monster out in action. Great job as always explaining in the detail the beast of a Capra !

😂😂😂😂😂

Quality review brotha, can’t wait to the videos of it in action, in love with those lights😍🤟🏼

Look at this beasty boy . Such a great in depth video as always brother. Looking forward to seeing her in action

Lol 😂

Love the personalization and showing us around dragonflight and Underrot. Great job as always brother !!

Like you said, how nostalgic. Gave me goosebumps when I saw Battle for Azeroth. Great video as always and welcome back, brother

I panicked because I thought that it doesn’t work 😭 Thank you so much you really helped me with that tricky lid

E10 is E10, doesn't matter if it's regular or hi test. The octane level does not effect the percentage of ethanol in the gas. No need to buy any higher octane than specified by the manufacturer.

I really like mine! I have used it for 2 years, but the tabs that hold the locking lid on broke now I have to hold the lid down for it to work. A replacement lid is on backorder. I will however buy a new one of these. I use the setting in between medium and fine and 12 cups. I use a funnel drip (there hole) and the grind is perfect and consistent!

You never start from go. You start from neutral. You are going to destroy ur transmission.

When you exercise that generator do you put a load on it too?

Cut out the"F" words and you can shorten your videos with no loss of meaningful content.