Відео

very interesting to see the whole process in completion, thanks

Popp

I have the same problem and needed to know the location of drain tube's. Thanks so much!!!!!

I recently purchased a PT1000 sensor with two wires and attempted to connect it to my RCT Basic hotplate. When connected to pin-1 and pin-5, it showed error 6. I then tried connecting it to pin-3 and pin-1, resulting in error 25. Could you please provide any guidance on how to correctly connect this external probe to the RCT Basic hotplate? Your expertise would be greatly appreciated. Thank you in advance for any assistance you can offer. Best regards,

My ambient temperature display shows up once in a while. My climate control works for 10-15mins then switches off. This morning it rained and my ambient temperature display worked but showed -6°c but the real ambient temperature was 20°c. This time around the climate control won't work. This afternoon once the weather dried up my climate control worked but only for 10-15mins. N.B. I recently changed the Aircon compressor. Do you think the external temperature sensor is faulty.

How to connect off mine hard to come off I took lol pipe out already

Great video. Thanks

Did it give any issues driving afterwards?

Goodnight!!

Thanks man! Very much appreciated.

I remember you describing this to me over the phone. Now here's pics!!

Buenas tardes, tengo un equipo parecido a éste del video si calienta pero no funciona la parte de la agitación en kas cuales el movimiento u oscilación es a través de bobinas. Que podría ser que esté dañado o alguien sabe como repararlo? Saludos desde México

I don't understand why after cutting the hole to change the pump, You then still dropped the tank?

My dumbass tried taking out the radio and now I have a car that won’t work cuz of the immobilizer code let’s see if this helps

Thanks

What length of cable would be enough for the front drains. I have a 60 inch one but not sure if it reach the end.

I did exactly the same thing to that plastic housing. I just turned it the same way I had on the passenger side. How stupid am I? I’d removed the headlights before without any problems…. Replacing that plastic housing would cost a fortune, I’m sure, if I could even find one. Who knows why VW designed it that way… 😢.

There isn’t many videos showing this. Thankyou. Most just show adding to the reservoir. It’s not easy to fill from that back area. It takes more than an average funnel.

So a 2011 side mirror can fit in a 2010 Subaru Legacy ? I’m asking because I need to buy a side mirror on Amazon but it says it won’t fit in a 2010 and there no other option so I need to know before just buying it

Thank you

Love how you hacked up the car just to do it the right way in the end. Why are people are so obsessed with cutting holes for fuel pumps when its easy to just drop the tank

Has anyone tried to cut into the plastic housing and just replace the motor w/o removing the assembly off the door at all?

That is only on your car or truck they are all different amd o not disconnect the same tho just a fyi

Can you help me for case Er 22 in my RCT Basic?

Lmao thanks for this video😂

Hi, thanks for the helpful tips. I was wondering if you might possibly have the ETS-D4 / D5 wire pinout? I’m about to hit my limit and brute force test it but don’t want to accidentally short the 12v to ground and hurt the board or thermometer.

PCV valve needs replaced/cleaned on these motors, it’s in the second hose you were pointing at on the drivers side cover.

Hello Stephan! I really appreciate the videos on the RCT basics. I have one that displays error 25 when it’s turned on. Resistance of the heater reads 21 ohms. Any idea what I should look for to identify what’s broken? Thank you!

disgusting

The correct way to remove the projector is actually heating up the assembly and pulling the lens off of the assembly. All 4 tabs should have been bolted down on all 4 corners for stability and alignment purposes.. Now, as far as the projector goes, the bowls can and do oxidize and there is no way to clean it at all. The reflective material would peel right off as soon as a cleaner was introduced to the projector bowl. If you were having a problem with getting good light output, buying the morimoto EVO-x2 projector would have been your best option. Extremely great cutoff sheld and great light output. As a tech, I wanted to point you in the right direction so that if you ever decide to do it again, then you'll have the correct information to do it right. This is by no means me criticizing your efforts. A lot of people have undertaken this task and did a lot of irreparable damage, and passing off bad information as the correct method of repair for this type of part. Most vehicles that have a projector from the factory will oxidize over time and people get really frustrated when they dump money on bulb after bulb trying to fix the problem when that wasn't the case. These Hella projectors are okay for what they are, but they do lack performance and like with most European vehicles, they aren't designed for the states weather conditions. Unfortunately all of this plays a roll in how long the projector will hold up, same thing with the electric system, especially the PCM. I'm getting ready to do the exact same thing to my 07 saab 2.0T wagon. However I will be doing a lot of lighting upgrades and I am seriously considering posting the entire process on UA-cam for people to see how it is done correctly. Again, not trying to criticize you for your efforts, just giving some advice on the subject if you decide to do this again. . Same process if you decided to do a retrofit build with a reflector type assembly, only a bit simpler because most reflector type assemblies don't have wiring harnesses running through the headlights.

You are a life saver, sir!

Thank you so much for this video

I need this done on an old Morticer one shank is .004 too big won’t fit in the collar all the rest of the hollow chisels fit fine except the 5/16 luckily it comes with a nice 1/4 as well

Thank you!!!!!! The most annoying shit trying to find that.

Electric 1/4 impact works wonders on those bolts. Filter number is 69710u.

Just pee in it 😂 but thanks for the video. Or van has been leaking all summer finally but the bucket and decided to fix it🥴

Boss music as the son joins the video

Good job.

If just replacing the center front mount - do you think it'd be best to just remove the radiator?

Today is Friday August 18.

Today is Thursday August 17.

Today is Wednesday August 15.

America's Food Basket Hyde Park 1.

CVS Hyde Park 3.

CVS Hyde Park 2.

can someon help he locate this range sensor please

Did cleaning the tubes work?

You captured the radiator drain plug on camera, and could have just unplugged it and let the radiator fluid run out instead of undoing the hose.

Опять ты ебланатор по 2 слова в минуту, так а дальше то че с ингибитором??

Ты мудила 10 минут ее снимал, так и че дальше то!??