![Spray iT SMART Repairs](/img/default-banner.jpg)
- 81
- 9 050
Spray iT SMART Repairs
United Kingdom
Приєднався 21 січ 2024
Smart repair on front bumper corner
Repairing Land Rover Discovery front bumper corner. Paint colour Indus Silver
Переглядів: 69
Відео
Smart repair on Land rover Rear bumper corner
Переглядів 86День тому
Repairing rear bumper on Land Rover Discovery in Silicon Silver and black textured plastic.
Smart repair on Range Rover Evoque front and rear bumper corner
Переглядів 5714 днів тому
Repairing Range Rover Evoque bumper corners. Car colour is Corris grey. Lacquer - Mipa cx4 Guns - Iwata LPH 80 ANI r150 Devilbiss DV1s
Smart repair on quarter panel and rear bumper corner
Переглядів 8121 день тому
Smart repair on quarter panel and rear bumper corner
Smart repair on two bumper corners
Переглядів 87Місяць тому
Repairing two bumper corners on Jaguar. Using Devilbiss SRI Pro Lite and Devilbiss DV1s
Smart repair on front and rear bumper Devilbiss GTI Pro Lite
Переглядів 85Місяць тому
Re-texturing rear bumper and repairing front bumper on Jaguar F Pace
Smart repair on Jaguar IPace in portofino blue. Rear bumper repair
Переглядів 72Місяць тому
Repairing rear bumper on Jaguar I Pace in Portofino blue. Lacquering with SataJet x5500 CC. Lacquer Mipa cx4
Smart repair on Land Rover Discovery sill
Переглядів 662 місяці тому
Repairing dented sill on Land Rover discovery
Smart repair Range Rover Velar, re-texturing plastic, front bumper respray
Переглядів 732 місяці тому
Repairing Range Rover Velar front bumper, re-texturing door trims
Smart repair on front bumper corner
Переглядів 522 місяці тому
Repairing bumper corner on Range Rover Evoque in Fuji white. guns used: Devilbiss DV1s, Iwata lph 80, ANI R150 Mipa CX4 lacquer with fast hardener
Smart repair on Land Rover Freelander both doors
Переглядів 4272 місяці тому
Smart Repair on both doors. Dent pulling and door colour change. Orkney grey.
Smart repair on Jaguar I Pace front bumper
Переглядів 1602 місяці тому
Repairing both front bumper corners on Jaguar I Pace. Colour name corris grey.
Quick smart repair on Land Rover Defender bumper corner, Narvik black
Переглядів 582 місяці тому
Quick smart repair on Land Rover Defender bumper corner, Narvik black
Smart repair on Land Rover Discovery both front doors
Переглядів 3313 місяці тому
Smart repair on both front doors on the Land Rover Discovery in Santorini Black. Left doors damaged after dent repair and the right doors with a deep scratch touched up by someone before.
Smart repair on Land Rover Evoque. Repairing rear bumper and door
Переглядів 1003 місяці тому
Smart repair on Land Rover Evoque. Repairing rear bumper and door
Jaguar bumper corner smart repair Santorini black
Переглядів 733 місяці тому
Jaguar bumper corner smart repair Santorini black
Smart repair on Jaguar Xe sills and rear bumper corner
Переглядів 1063 місяці тому
Smart repair on Jaguar Xe sills and rear bumper corner
Smart Repair on Range Rover Evoque Eiger grey SataJet x5500 CC
Переглядів 1213 місяці тому
Smart Repair on Range Rover Evoque Eiger grey SataJet x5500 CC
Smart Repair on Jaguar F-Pace door and tailgate
Переглядів 1174 місяці тому
Smart Repair on Jaguar F-Pace door and tailgate
Nissan 350Z headlights restoration. Devilbiss DV1s
Переглядів 784 місяці тому
Nissan 350Z headlights restoration. Devilbiss DV1s
Quick Smart Repair on Range Rover Velar bumper corner. Devilbiss DV1s
Переглядів 614 місяці тому
Quick Smart Repair on Range Rover Velar bumper corner. Devilbiss DV1s
Smart Repair on Jaguar I-Pace door. Iwata Bellaria 007 Secret Agent Limited Edition
Переглядів 624 місяці тому
Smart Repair on Jaguar I-Pace door. Iwata Bellaria 007 Secret Agent Limited Edition
Smart repair on Jaguar F-Pace Front and rear bumper repair. Devilbiss DV1s
Переглядів 1154 місяці тому
Smart repair on Jaguar F-Pace Front and rear bumper repair. Devilbiss DV1s
Smart repair on Land rover Discovery. SataJet X5500 CC 1.3I and Devilbiss GTI Pro Lite te10
Переглядів 2734 місяці тому
Smart repair on Land rover Discovery. SataJet X5500 CC 1.3I and Devilbiss GTI Pro Lite te10
Smart Repair on jaguar XJ Cracked splitter, front and rear bumper. Devilbiss DV1s
Переглядів 1794 місяці тому
Smart Repair on jaguar XJ Cracked splitter, front and rear bumper. Devilbiss DV1s
Smart repair on Range Rover Velar. Devilbiss dv1s
Переглядів 804 місяці тому
Smart repair on Range Rover Velar. Devilbiss dv1s
Smart repair on Jaguar XE front and rear bumper corner. SataJet x5500 CC
Переглядів 1484 місяці тому
Smart repair on Jaguar XE front and rear bumper corner. SataJet x5500 CC
Stone chips repair on Jaguar XE sills and quarter panels. Devilbiss DV1s
Переглядів 654 місяці тому
Stone chips repair on Jaguar XE sills and quarter panels. Devilbiss DV1s
Dude you kept that one crazy small! Good job man. I’m sure you have said it before but what clear are you using?
Hi. My clear coat so far is mipa cx4 but I'll try proxl 405 rapid hs clear soon. Thank you for your comment.
Dude I love your videos. I do this stuff too but your clear comes out so clean! Im spraying out of a garage as well and I’m wet sanding a lot after paint
Hi. Thank you for your comment. Regarding your problem with getting bits of dust etc. try to spray water on the floor around, use tacky cloth and try to keep it clean as much as you can. I get bits as well, it's a part of garage painting unfortunately. Once again thank you for your comment
Nice job but video would be better if you explained each step with voice over or as your going and not just music for the whole video.👍👍
great job mate 👍👍
Thank you
Good one mate...from Kiwi
great job 👍
Thank you. Got a few more to upload
Great video mate. Can you tell me what primer you are using 1 k or 2 k ???? What brand
Hi. At the moment, for small repairs like this, I use 1k primer, and it is mipa 1k n45 and you can mix it with 1k plastic primer instead of thinners.
Thanks mate from Kiwi
great job mate 👍👍
great job mate 👍👍👍
Great job mate. I noticed you never use a plastic adhesive promoter on your bumpers ? I presume it’s a personal choice thing as many don’t seem to . Do you get much crap in your clear not having a booth ? I have a small DIY booth in my garage , all sheeted off and deep cleaned before I spray , yet I get so much crap in the clear it’s driving me mad , even wet the floor but still no change .
Hi. I do use plastic adhesive, but not often. More likely for new parts. Primer I use its also designed to spray plastics (that's what tds say) never had any problems. I spray Primer after 320 grit sanding so it's stick better. Some people add plastic adhesive into the Primer as a thinner. I do get a few bits of dust or dirt, but not much, to be honest. If you do get 1500 wet sanding, then trizact 3000 and polish it off. I had a bit of problems with water condensation in the compressor tank, replaced the air filter for a sata one, and all problems so far gone.
świetna robota kolego, naprawdę podobają mi się twoje filmy, tak trzymaj 👍
Whats your primer gun?
It's ANI R150 1.2 mini gun
@@radekkiko 1.2 can shoot primer? 😳
Well it depends. I use for small repairs 1k primer which you can. You can just add more thinners in to it. Its a different story if you use 2k primer but still can be diluted with thinners@Rikats15
great job mate 👍👍
Hi. It was a quick one. Literally like half an hour job.
great job mate what clear you using?
Mipa cx4
Perfect job. Why are you using 1k primer not 2k?
Hi, it's just easier and quick. For bigger repairs, I would use 2k. I can leave it in the pot, and it will not go off like 2k
@@SprayiTSMARTRepairs also on metal small repairs you would use 1k? It will not rust through later?
@@Rikats15 most of smart repairs are done with aerosol 1k primer. A good one is sikkens spot primer. And no, it will not rust through later.
Top job once again
Thank you
Thanks for the videos. Great stuff. 👍🏻
Glad you like them!
👌👌👌👌👌👌
love the channel mate you should do some talking get over your fear 🤣👍 i take it you do trade work for jag/landrover
Hi there. I'm thinking of that, to be honest. And yes, I do look after one of the JLR dealers
@@SprayiTSMARTRepairs you should do mate 👍
@grantssmartrepairs The plan was to go work for myself and get a van or unit, but these days are not that easy, or maybe I'm too scared.
@@SprayiTSMARTRepairs mobile life is hard with our rubbish weather I do really enjoy it tbh but loads goes wrong, units are hard to come by and cost a lot to run but if you can get the work it’s definitely worth it
@grantssmartrepairs well plan has been upgraded and thinking to move to other country like cyprus where I'm at the moment For a week to see how is life here. There is one guy in South cyprus doing smart repairs. Maybe I'm gonna go and see him. To talk abeout how things are going on here. See, there are a lot of tourist driving cars around and renting car places
Big one! Love it dude keep em coming. What primer and gun are you using? Thanks
Thank you for your comment. Primer gun Ani r150 1.2 mini gun Basecoat gun Devilbiss gti pro lite 1.3 te10 Lacquer gun SataJet x5500 CC 1.3 I pattern Primer I use its 1k high build.
great job mate 👌👌👌
great job mate 👍👍
great video mate just found your channel subbed 👍👍👍
Wel don smal shop and it's working for jou
Whats the pressure when your compressor kicks in to fill tank?
Hi. I have readjusted the pressure switch on the compressor slightly. Now it is switching off at 9.5 bar and kicks in at 5.5 bar . Now it's more stable with the pressure at the end of my airline when I'm painting bigger jobs.
Another great job hats off to you
Thank you so much 😀
Great job , must of been a bang on colour match to blend that door repair. Fair play looked awesome . Was that a lph 80 ?
Cheers for the video. 👍🏻
Good job ...What primer are you using ???
hi.it is sikkens spot primer
Thanks Ill try it....
Awesome job buddy . Was that the standard shade of hydro ? Brilliant blending job
Very good mate from ...Kiwi
Very good mate from Kiwi NZ
Great job as usual mate. Took the plunge and ordered my new hydro paint scheme today, can’t wait to give it a test. I had a couple of questions regarding the hydro - can you use anything else in place of hf900 to make it cheaper ? Also wondered what your palm sander is ? I have a Mirka air one but I really want to change to electric
Hi. Thank you for your comment. Regarding hf900, you use around 10% of your mix, so it is not too bad. You'll need lechler map 4 app to mix colours. And my sander is a metabo 5" electric and its a same as mirka electric byt slightly cheaper. I'm very happy with it, really good quality.
Hello, thank you for the videos, they are good! I have a question after every job you do a polish-gloss?
Hi. Thank you for your comment. Yes, I polish them.
Great job as usual . Any reason you used the solvent on the base coat rather than the water hydro
hi, not really , just had some solvent pre-mixed
Great job again , top notch . What paint scheme do you use ? I’m thinking about pulling the trigger on lechler hydrofan scheme. Any good ?
hi, im on hydrofan and its ok. sometimes the new colours a not great but its a simple scheme and not to expensive
@@SprayiTSMARTRepairs I was wondering if HYDROFAN do a clear base coat for a wet on wet application, to help Metallics to lay down . I’ve been looking at there products and can’t work it out .
easy blending 777 hydrofan
Cheers mate
Flawless 👍🏻 Love this kind of content
Thank you
Just found your channel , great vid. Your channel will grow fast if you give more information on the procedures / tricks / grits and products used for each stage. People thrive on information for this sort of thing .
Thank you for your comment. I'll try better in the next video. Maybe in the future I'll try to talk instead. Will see. I'm a new to UA-cam and a bit shy 🤭 Once again, thank you for subscribing
@@SprayiTSMARTRepairs you might find it easier and less time consuming to film the videos , then put a voice over later on as the video runs through . I’m no youtuber but it seems a popular way to do it. Gives you time to edit things and anything you forgot to mention on the fly . very interested in painting / finishing
@lockstocky2800 Yes ,that is what I was thinking of doing one day. I'll see. And that's how I became a painter by watching others paint about 8 years ago
Very good! The car looks good as new
Whats your compressor setup?
150l
Nice work 👍🏻. Love this kind of content. Keep going 👍🏻
Thank you.
Why you don't use dv1s for base ? Lph80 is better than dv1s for base?
@M99pt I do use more iwata lph for basecoat as its a lot more precise, less overspray. Obviously you can use dv1s for base coat. They come with two air cups from factory. One designed for lacquer and other one for basecoat(hvlp like) so you can choose. Sizes 1.0 and 1.2 withe every gun. Thank you
Awesome video brother 👍
Thank you
💪💪💪💪what do you think about clearcoat without thinner?thank you
I always add a bit of thinners. It just helps to dry quicker and lay down lacquer better. I use mipa cx4, which is hs lacquer in cold weather a bit thick, so it's a thing to add a bit thinners. But it's al depends on how,what, and where you painting
Piesek króluje w internecie daj pieskowi stęka 😊
Pępuszek