Відео

Hi, I have the 100 and I got sparks coming out the exhaust, and not power, what u think

smart with the foil around the pipe; helps get that smoke up and out.

Hi great video, could you share the part number or link for fly wheel side seal, also how you removed old seals, thanks

Do you have an easy way of getting the oil hose that goes to the chain through the hole in the body of the saw. Mine was super tight and didn’t really like the way it fit.

good job .i made one my self out of a drill bit but i used a lath to make mine and it works great !

happened because your bushing is missing

What is that little plastic piece under the float for

Thanks for the upload...Going to do mine right now...

awesome job thank you

You can use my press it might be easier

I think my Echo CS-400 has a bad air leak. It idles at half throttle in spite of all tuning. It has a new carb and new fuel hoses and tank filter. It about has to be the crank seals. I like the innertube to block the exhaust and intake. Inter tubes are high now just like everything else. I wouldn't have thought it would leak around the outside of the crank seal but there it is. Do you recommend any type of sealant around the crank seals?

Yes!, i was thinking about doing that if the little dial adjuster does not work right, thanks for showing the grooves behind the sheetmetal, i was wondering about that. I might have to fire up my Dremel. Thanks, and hello from Alaska. Be Kind, be cool and be careful.

Mine carburetor pain .

Starting fluid cheap .

Them saws pain in the ass .

does anyone know where i can find parts for this EHO CS450 chainsaw thanks

flippin' amazing! you make it look so easy, mesquite aint no joke

What size socket and was it six point or 12 ????😊

Great video sir....the commentary is very well thought out. I can't believe this video hadn't come up yet as a recommendation for me to watch.

That sounds pretty darn good, but it needs more 🐄Cow 🔔 Bell

I bought the rear axel square key but it is too long. How long should the key be to work properly?

Sir you do good work, thanks

Sir you really should clean it up spotless first to ensure contamination into the bearing 🇦🇺✊🏻

❤John 3,16 ❤

Polarity reverss after hiting flywheel??? amm okey i need weed for the first time of my life

Nice place thanks for the video

Wished you would have showed removing the old one. Mine leaks from the bearing, not the seal.

Thanks Partner! Appreciate your video.

Catalyst not catalink

Mine has fuel shooting out of both sides of the top. Think my floats are to high? Stops shooting gas out at half throttle or so. But idle it’s like a fountain

Good luck brother. I subscribed.

My 1010 ProMac is smoking little extra. That a sign of bad seals?

4 90s dude purple primer clear glue medium set Blue glue sucks

4 90s dude

Brother I’ll be honest this is not good. Always primer PVC, although it may not call for it, the process of priming takes seconds. Next you never ever use compression or telescopic pvc repair couplings. They break 100%…use a schedule 80 coupling and a schedule 80 union. Keep making the videos brother and have a good day.

I am so glad I found your channel! I recently came into possession of a Stihl 034 that was apparently used as a parts one. It’s missing everything that makes it’s growl. It’s going to be a fun project and your videos will help immensely!

It works better to put the wires below the pipes so they aren't the first thing you hit with the shovel when digging in the yard.

No primer that’s called a jerk move

Just curious why you're not using purple primer with that hot glue.

It works better if you put glue inside the fitting first cause it’s protected from the wind and air. It’s not a huge difference but it helps bottom out you fittings

Is this heaven😂😂😂

Menarik untuk di tonton

I just pulled off mine of my tractor thinking it had a knocking sound but after hearing yours it's normal I'll just put a seal and put it back on thanks for the video

Great job Sir. I wish some of these firearm manufacturers would take on customer requests. Sometimes I see a feature from one gun that I think would be great on another, but they will not sell the parts needed, or even a blank to do my own work. For instance, I have a Taurus Tracker in 41 magnum, and I think it would look really cool with a 3 inch Judge profile barrel on it instead of the ported one it has. I know the Judge will have the 45 bore diameter, so I wish they could sell me a blank or something and I could have it bored and rifled in .41 caliber. Only other thing I could think of is to have a barrel sleeve installed, but I'm not sure the original barrel has enough diameter to do this. I know S&W has their sleeved Governor model that looks similar to the Judge, but I know the Taurus won't have the indexing tab for the shroud, and I think the Smith is a larger frame anyway, so that might present another alignment issue.

little 250 straight 6? 283?

That's some wet snow! That's either gonna melt, or it's gonna freeze under a thicker fall. 😅

Damn that shit look buss fr fr

Im from Québec. We use to it... 👌😃👍

I love my 82. I hope it turn out great!

Please make more cold starts just like this. Loved watching you start it up! And it sounds great too.