- 39
- 102 160
JEREMYS SPEED SHOP
Приєднався 30 кві 2017
General automotive and small engine mechanics, welding and carpentry
2018 Polaris throttle safty switch/limp mode - fixed with two old resistors from scrap electronics
2018 polaris sportsman 570, bike was on limp mode, trouble code 520 194-2
throttle release voltage out of range, two pins for throttle safety at right hand control showed an open circuit
throttle release voltage out of range, two pins for throttle safety at right hand control showed an open circuit
Переглядів: 1 728
Відео
Here's a great thing that I'm doing in the shop for tool organization, its called French Cleats
Переглядів 93Рік тому
Here's a great thing that I'm doing in the shop for tool organization, its called French Cleats
Honda 500 Rubicon has a seized rear brake arm(shaft) (drum brakes)
Переглядів 695Рік тому
Honda 500 Rubicon has a seized rear brake arm(shaft) (drum brakes)
Check out this tow behind mower, exhaust is coming out of the carburetor and it still runs!
Переглядів 123Рік тому
Check out this tow behind mower, exhaust is coming out of the carburetor and it still runs!
Junk DS 650, look at how they tried to fix the flywheel nut!!
Переглядів 150Рік тому
Junk DS 650, look at how they tried to fix the flywheel nut!!
Here's the electrical plugs I like to use in the shop
Переглядів 41Рік тому
Here's the electrical plugs I like to use in the shop
How to remove an Arctic Cat ATV axle that has a white stripe
Переглядів 1092 роки тому
How to remove an Arctic Cat ATV axle that has a white stripe
Replacing ski-doo QRS Secondary clutch rollers
Переглядів 14 тис.2 роки тому
Replacing ski-doo QRS Secondary clutch rollers
How I made a Water Level
Переглядів 112 роки тому
This is my take on an old leveling tool, how i made it and a little info on how you would use it
700 Yamaha Wolverine leak down test and compression test with a blown piston
Переглядів 832 роки тому
700 Yamaha Wolverine leak down test and compression test with a blown piston
Part 4 shop build
Переглядів 72 роки тому
Part 4 of my new shop build, front and side wall framing you'll see how I was able to lift the walls by myself
Garage expansion part 3-Forms, foam, pipe and cement
Переглядів 102 роки тому
Garage expansion part 3-Forms, foam, pipe and cement
Honda generator no start, carb clean, new gas and oil change
Переглядів 212 роки тому
Honda generator no start, carb clean, new gas and oil change
Yamaha wolverine 700, piston is toast!
Переглядів 222 роки тому
Yamaha wolverine 700, piston is toast!
How most ATV throttle safety switches work
Переглядів 8 тис.3 роки тому
How most ATV throttle safety switches work
How to reset a brute force 650 belt light(if you don't have the gray plug)
Переглядів 22 тис.3 роки тому
How to reset a brute force 650 belt light(if you don't have the gray plug)
Rebuilt the top end in a '94 ski-doo MX 470
Переглядів 2,7 тис.3 роки тому
Rebuilt the top end in a '94 ski-doo MX 470
Figured out what's wrong with the ODES transmission
Переглядів 6 тис.3 роки тому
Figured out what's wrong with the ODES transmission
Odes SideXSide transmission trouble
Переглядів 1,7 тис.3 роки тому
Odes SideXSide transmission trouble
2015 yamaha SR viper 1000 engine assembly
Переглядів 1,6 тис.3 роки тому
2015 yamaha SR viper 1000 engine assembly
2012 Arctic cat HCR M800 chain tensioner fixed
Переглядів 5 тис.3 роки тому
2012 Arctic cat HCR M800 chain tensioner fixed
2002 SKI-DOO MXZ 700 gets new slides, carbides, chaincase oil
Переглядів 6 тис.3 роки тому
2002 SKI-DOO MXZ 700 gets new slides, carbides, chaincase oil
God that clutch is smoked 😮😮😮
My bike is the same fuckin way.
How did you solve this Problem ?
great job.
Will this help with oil consumption? Mine uses a quart of oil for every full tank of fuel.
No the valve clearance has nothing to do with that, could be passing the valve stem seals but it's most likely passing the piston rings, you'd have to do a compression test and a leak down test to see
Mine is doing the same as the 500 ho. I have a 2005 500 ho and it just recently started to be hard to start. Have to do the same as touching the throttle a lil. Will this also cause the machine to turn over slowly, because ever since it started this problem it turns over so slow
No I don't think it would cause that, if anything it should be easier to roll if a valves hanging open, your battery could be getting old, starter could be dirty, I'd check also the air intake for restriction, try it without the airbox lid and filter, one time I had one with just a really dirty air filter caused hard starting and it didn't run right
Awesome job
If your going todo it that fast why bother filming it
Same issue as the other one? What was the issue that it was having. Mine is hard to turn over when it has spark plugs installed and when the plugs are removed it turns over nicely.
Tip, adjust with the feeler gauge in place and you won’t have to guess.
That clutch is slipping like craaazy holy shit did you not notice that? Sounded barley ridable
Can someone help my Polaris sportsman 500 4x4 we put two engine of the same kind together and it cranks and cranks but don’t start or nothing not even on starter fluid
valves too tight? i find theyre like that if the intake valves are hanging open a bit, do you have it timed correctly?
@@danielestvanik9847 I’ll hanks for the help but I orderd a top end kit and it runs like new now
Does the side cover use a gasket or is it rtv?
RTV
do you have to do the compression strokes?
has to be done when the cam lobe is not pushing on the rocker arm at all, I think its called the base circle, that's where you would measure the clearance, when the engine is on the compression stroke all valves are closed so that's where you need it
What was the atv doing prior to valve adjustment would've been good to compare indifference
Bike didn't want to idle when cold, had to hold the throttle to keep it running until warmed up
Throw some Dynamite in the Fuel tank .
What model do you have?
Don’t think it’s supposed to smoke
ye its not
probably alot of shit in the engine just have to rev the shit out of it and will not smoke
@@admiralclawz8524 yah it cleared right up
Just do a engine rebuild
How do you rotate the crankshaft to find tdc? I see the drive cover is still on.
I take the spark plug out so it's easy to roll and use a ratchet on the cam sprocket bolt. with the plug out I put a screwdriver in the hole to find TDC