- 2
- 141 489
Steve B
Приєднався 17 жов 2011
Bobcat 873G 15-02 Traction Lock Pull Solenoid Error On - Diagnosis and Repair
This video describes the diagnosis and repair of an intermittent 15-02 error I have been experiencing with my Bobcat 873G. It seemed to happen more often while waiting for the glow plug count down to complete. The check list for the diagnosis is posted in the video. In my case, all of the checks for harness wiring and controller indicated a bad traction relay. I suspected the relay was okay and the issue was related to how the relay was seated in the fuse and relay panel. In the video, I demonstrate how I checked to make sure the relay was okay that led to suspecting the panel. I have added about 5 hours to the Bobcat since seating all of the relays in the panel. However, I do think it is possible for them to become loose again sometime in the future with normal operation. Let me know if you have any questions.
Update 02/23/19: I've put another 20 hours on the machine without an issue. If you have resolved your own 15-02 error, leave a comment and let's know your fix.
Update 02/23/19: I've put another 20 hours on the machine without an issue. If you have resolved your own 15-02 error, leave a comment and let's know your fix.
Переглядів: 112 748
Відео
Bobcat 873G 32-40 Error (Lift Handle not Calibrated) Diagnosis and Repair
Переглядів 29 тис.7 років тому
This video describes the repair for a Bobcat 873G (AHC only with metal controller) that was consistently throwing a 32-40 error over the last 30 hours of operation. A similar error for the tilt handle is error 32-35. Initially, the error would occur when operating the lift and tilt handles at the same time. Then, after replacing the actuator and spool rod seals (to be shown in future video) an ...
I have a problem with Ghel It works for five hours, then the engine starts to vibrate slightly for half an hour, then it turns off, so I try to start it again. It works for a second and turns off again, then it is left for some time and it returns to work. What is the reason?
I would look for a fuel starvation issue. Check the fuel shutoff solenoid make sure it is working. Do you add fuel after the 5 hours of running? If so, Bobcats use a fuel pickup tube and you might an issue with it. I am not familiar with Ghels and these are common issues with older Bobcats.
what pin should have voltage in the socket ? when keyless pad is turned on
Remove the traction lock relay and if the code remains then pin B, wire 4100 in the traction lock solenoid connector should have 12 volts. I could send you an image of the complete test for the error, if you want.
Tengo el mismo problema pero no me llega la señal del ecm a los pines del relay
Verifique todos los pines en el conector J3 en el ECM. A veces retroceden en el conector y es necesario volver a colocarlos. Salud
@@steveb153 bro no me llega una señal al módulo que va al relay y dela relay al selenoide del freno
@@cristianmorales5154 ¿Tienes un correo electrónico con el que pueda contactarte? ¿Se muestran otros códigos?
@@steveb153 si dos códigos pero no no es con el problema que tengo
@@cristianmorales5154 Además, ¿cuál es tu modelo de Bobcat?
I'm sorry not All people have mechanical abilities
Hi! What brand and model of multimeter are you using in the video?
It's an Ideal model 61-361.
I hope for a reply that has a Bobcat S130 2008 screen that disconnects the electricity while working
I hope for a reply that has a Bobcat S130 2008 screen that disconnects the electricity while working
loose connection?
Where does the bobcat 773 has the fuse box .
Bottom right of the engine compartment.
I've got a S160 with the same electronic security system as you do. When I press the run/enter button on the security panel, it no longer powers up and asks for a code. Any ideas?
If you have the deluxe panel it sounds like it could be locked. Anyone else use the skid steer besides you? If I lock the panel I use the 4 digit code I set up. If you think it might be locked there is also a master code that you should be able to get from a dealer. They can look it up by serial number. My master code is a 6 digit code.
@@steveb153 If the panel were locked, would it (the panel) not power up asking for a code then or would it atleast still power the panel when the button is pressed?
@@spyderjosh Yes, it should power up. I read your reply as if it were asking for the code. Sounds like a panel issue. My panel is not hard to remove and you can check for power getting to the panel when you press enter/run button. That's where I would start.
Is it possible to upgrade to the deluxe panel ?
When all 3 lights on top left screen are on t190 will not move when only one is on all is well thanks hc
Are you getting the 15-02 code when you try to "Push to Operate?" Sounds like the Traction Lock light is not off. If that is the case the traction lock solenoid is not pulling the pin to allow the loader to move.
Trying to locate the traction lock solenoid. Any pointers on where to look. I haven’t washed it out or really dug for it yet. But didn’t see it just glancing under cab.
Sll three lights on top left screen flash and when this is the case t190 will not move if only 1 light is on all is well thanks for any help hc
Did anyone understand my problem on t190 bobcat
Yes , Thanks
Vi plz my help my excvator not starting as plz help
Plis help my
The laigh don't turn on
My bobcat is locked I can pick up the buket
Does it lock up when you only use the tilt? What error code do you see? What model Bobcat do you have?
Great patience! I'm diagnosing lift and tilt actuator errors myself. Pretty sure the potentiometers are bad in the actuators. I wired a automotive throttle position sensor into one to verify.
No Speak inglish
María Guerrero Salasar lo único que dijo fue que nomas checke las connections por atrás del panal del relay, que los empuje y que aver si están flojos, sorry si mi español no está tan bien
@@hmproductions2618 gracias
@@mariaguerrerosalasar560 mmm 8 8mh
?
Xx
I have a friend who needs someone to do this to his bobcat know of anyone willing to do so!
Hi Amanda, where are located? I might be able to help.