Відео

I opened mine up and the condenser inside was wet !!! Should I be worried ?

Great video ! Well done... very helpful for replacing the one on my wife's 2011 Nitro

Thank You.. Its good to know what to expect to see before tackling a timing chain job.. Well done.

hell yeah...that clip that goes through the hole in the window was hardest part for me. felt like i was gonna break the window. couldn't have done it without your video... thank you

Does it have a gear position as one of the data fields I can set on the main screen ?

Remarkably well done video, even without factoring in the one-handed camera work recording the other-handed repair work!

Mine doesn't have that lol

You are an angel best explanation on the web on this engine!! Short clear and to the point i was going nuts trying to find the crank mark 😂👍

Great video thhanks!

I overhaul the cylinderhed now the car have a high and low idle need diagnostic

I now know why the plastic was cut. Just went to change mine on my ‘07 Avalanche and it comes SEALED from the factory. I will have to get my dremel and actually cut a notch out like the previous owner did to this one. No other way!

My car cant start after all the timing marks are on the position,what could it be

This helped, thanks man

Loved it! Just did it today after watching this video. No bull crap, no adds, just a simple video on how to do something

Just love it when the manufacturer is super vague with the timing marks or the method isn’t a very exact one.

Okay check this out I have a 4.7 engine and my starter is on the passenger side of the engine and I’m trying to figure out what model 4.7 I have TIA

Thk you 🙏

That's a front oil seal leak you got there, better to do while off.

Nice!

I didn't believe it when they told me

It does nt start

Great video. Would like to know a cool way to clamp that piece behind the door lock. I had a time with that 😂

Some torx head sockets. well done on the commentary

Thank you😎

The forbidden kool-aid

5/16 = 8mm dude

I was so mesmerized, I watched til.the end. Bad timing on air compressor though...😊

Thanks

What model is that new panel? Mine is the back passenger side. Thank you so much for the video! It was great!

Can the screen flip up side down if I want put it on the windshield?

It's strange all windows won't work except rear left passenger

Are you in the US?

How to clean the connector.

Followed everything you did step by step and saved me a bunch of money 👍 thank you sir 🫡

Thank you for the video bro ✅

Any chance you know how to do the timing setting from scratch? My timing chain competently broke. I have purchased new components and want to reassemble. BUT.. I am guessing that even if I align the 2 marks with the chain, there still is likely 1 of 4 rotations that the crank and cams could be on? Any help or suggestions would be appreciated.

How do you sync they threw a 2 x 4 op they have planers it is perfectly straight. No you can’t use a planer on a head you can use a belt sander. You can use a planer before they had machines they done it this way, and it always worked now we have technology to use Laser perfect machines but this way works people don’t have deep pockets. They have to compromise. They have to get their vehicles on the road. They got a warpage in the head they could clean it up with sandpaper it works. It does a job it’s old-school trick a lot of people don’t have deep pockets for the machine shop parts are outrageous machine shops are outrageous.

I can't get the glass out. I can push that tab but can't get the glass to release. Is there a trick to hold the clip and remove the glass??

Thank you!

What kind of sound do you experience before replacing the tensioner pulley? I am experiencing a chirping sound when in D mode and i already replaced the serpentine belt but the chirping sound are still there. 😢

incase I can't do it myself where could I take it to get it fixed

Your video is awesome I don’t have to listen to people talking about fishing and other stuff that’s not important just the markings and that’s what I needed and I got it quick. Thank you very much.

Awsome vid.

you dont have to hold the key for it to turn over just bump it it will start my do every time

.027 - .030? All the forums I have read say the proper gap is .036. Is this the 3.2?

Well done.

Amazing engine

Would have been a good idea to show your way of removing the intake. Another guy did it but he took of many little parts and sensors which yours does look like they are removed, only if you could show what you exactly removed. This video doesnt help me as I know thats how you remove ghe starter but not sure of how many parts I need to remove and which way us easiest.

I had the issue of the connector to the rear bulb assembly, not having a thick enough ground wire, so the housing had melted around the ground wire. I ended up soldering a second ground wire between the two, which has worked perfectly so far.

Thank you for this. I started with the initial take out the screws then start prying and yanking and the door panel wasn’t budging so I thought I better check on UA-cam lol. I’ve done regulators probably close to 10 vehicles over the years and this one is near the top on the pain in the ass scale. Made better by this video. 👍