Відео

Unless this is an old video that’s been corrected over 10 years ago.

No offense, but Muriatic Acid does the job too. I have cleaned many of those skimmers and pump baskets You’re welcome!

i live in the philippines and my roof is 3/4 ''plywood with a tarp stapled over it the sheet metal is heavy gauge corrugated. and my screws are in the flat to stop typhoons from removing the sheet metal. ridges wont cut it. i screw every 6 inches in rows 4 foot apart. its painted over with iron oxide primer and hi gloss white oil enamel. my washers never get sun or rain on them. i spot sand and repaint every 3 years and being white the roof is 70 degrees at hi noon in july, my washers dont get baked.

You're 100% correct in terms of not over tightening the screw to prevent damage to rubber washer and avoid leaking, but infact you don't exactly know where to screw, thats not the correct place my friend.

Top ridge budy.....

The lip of the strap shold b above the reef line sir

Never screw on the flat always on the ridge

I would get longer screw it on ridge side of metal roof to prevent leak.

I couldn't help but notice the single 120 gallon propane tank. Is the Generac running on natural gas or propane? If propane then how is that single tank for prolonged outages? My installer recommended to have at minimum two tanks.

Put on top!

The string line for straight fastener line is a great touch also

Thanks

Our County would never let us do the electrical like that !

Fasten on the ribs, you’d deform the panel shape before deforming a quality sheet metal roofing screw rubber washer. The water falls on either side of the rib and onto the flat. Painted screws are trouble, outdoor rated fasteners should be stainless or galvanized at minimum

There was a time when that didn’t need to be said

Scew on the ridge and you won't get a leak.

No impact gun and screws onto the ridges.

O boy your gonna loose that black and blue nail. Been there done that.

Yep and be prepared to recheck every single one of them every year or two.

You should use a screwdriver impact or a drill or get a app capable impact for the proper driver torque for the fastener. And using your own tool like this is valuable to know it's settings and abilities for the tool and yourself

“Put the screw in the rib!” 🙃 I came to the comment section just to see how many people are ignorant of manufacturer specs and warranty compliance and say he shouldn’t put the metal-to-wood screws in the flat. I was not disappointed.

Yeah, if it does leak a little bit, just go out and buy some real good exterior flex seal just to get you by for the next 20 years of your life stuff works great. Have a good day.

Amish use yankee screwdriver seems to set them perfectly. But don’t try it unless you ready to find out how good you ain’t .

Just like a zero turn

I had a standing seam metal roof installed instead and eliminated a potential problem 😂

Can you use rivets and avoid this problem?

Is this a joke channel? Because if you did that here in Australia were tin roofing is the norm you'd be kicked of site.

Unless it has a solar panel recharge ability, I find this to be more useful as an indoor camera where you can hang it near the ceiling in some corner of a room or entry way of the house or garage

Those screws are tiny

4/0 al give you 189 amps 250mcm give 215a

Hello this is Sunny from Steelmama China, if you are interested in any machine. Contact me freely

No it doesn’t help, what would help is someone other than me taking out every screw and replacing everyone on my 15 year old roof that the washers have dried out and cracked and now leak

Con il tempo perde quella vite... fenomeno 😅😅

It's not the Mona Lisa if you can't eyeball those screws and gets them even enough so they look fine your eyes are bad.

Let me buy the old one

I’m looking for how to fix it not how to get ripped off.

Does anyone make a tool to keep from over torturing?

When removing the oil filter put a large ziplock bag around the oil filter it will catch any oil

and that’s why we by bootleg parts and bootleg install em

Should have gone to an industrial bearing supply. I'm sure it's the same as the bearings I replaced in a tk 5 speed a few years ago. Dealership wanted $450 for 3, auto parts stores wanted $250, local industrial bearing supply charged me $125 for better quality than OEM bearings.

The price of machine and truck parts are out of control. A new air dryer for my rig was $45 four years ago. Just paid over $200 for the same darn part. Grrrr Bidenomics😢

Easy fix.

It's a pillow block. Just roll a new bearing into it

Thanks for voting for Nafta.

And I bet that bearing only has a blob of grease in it the size of a pea brand new

Context? I’m just don’t know what’s going on

Parvis Bearning .has many types of bearings

How would you go about making the original opening half an inch wider to accommodate the new sidelight. I’m thinking jig saw?

Yep, many don't understand especially these days with modern powerful drills and impacts.Idealy you want to seat the washer not drive it to China.

Did he run unfused conductors with fused conductors in the same conduit?