- 4
- 65 794
elluigi69
Приєднався 21 бер 2013
Відео
Chevy,gmc,yukon,Keyfob programming 1996,97,98,99
Переглядів 63 тис.9 років тому
Part #16245100_29. 16207901_5 only. And just keep jumper wire in place port 4 and 8. until u finish programming all of the keyfobs u will plant to use. Wen u r done with the las key fob. Remove jumper wire.
My type r stock bottom.gsr head.skunk 2 im,70mm tb
Переглядів 53310 років тому
My gsr Type r bottom block,gsr head stock.
Переглядів 1,5 тис.11 років тому
This video was uploaded from an Android phone.
Do you have a link to the correct keyless entry because I can’t find one with the same number on amazon
Quick and easy , thanks for the vid
Where do I buy those key fobs
Got mine on ebay.
Works perfectly!!! Thanks
Some people shouldnt upload videos if u cant keep camara from moving
Thanks bro. Worked great.
Im glad it did.... 👍
How’d you like that setup ? I got something similar swapped into my coupe. tryna tune it now. Not cooperating.
Adam Cross. Turned out great. I did the chip burning myself.
2000 yukon?
How about 2000 pins don't match
David Minervini different after early 99 models
I still have my factory key fob that has seemed to quit working I have put extensive sound deadening n my Truck and wondering if I could be blocking the sensor maybe? Where is the sensor located? Also could my factory key fob lose its 'link'? Thanks man tired of using my key to unlock truck manually
Daniel Harrell im not sure were it is. Im assuming. Its on the ingniton assembly. Or something. Not sure. But try a new battery for ur keyfob.
If ur inside the truck does it work? If so then maybe the sound deadening stuff is blocking it. But check your key fob battery. It wouldnt hurt to try and reprogram it. Hope u figure it out
Remove the cover on the fob and pop the rubber cover off the board. If the buttons have left black residue on the board contacts, clean it off, alcohol or electronics cleaner. snap back together and check if it works.
Rip. Integra.
Rip my integra..
what harness did you use for this swap please help
@@CarsWithAttitude same LS Engine harness. Just ran a couple wires to the vtec system to the ecu.
What happend to your car? Also I am building a type r bottom end and I'm not sure what head is best the b16 or gsr head to go with. Any advice on that?
I think not. but try it..
I have a key fob room my 03 GMC envoy would it work in my 97 Silverado
yes. as long that is the same year. and part #
Will this same step program the truck, too?
Yes
and chek the s fuse box.
zalem. if it didnt do anything. ur vehicle may not be equiped with keyless entry. or just make sure part numbers match with thw ones above I stated.
and part # listed above, only will work.
zalem.. make sure ur vehicle is equipped with keyless entry.. if its not equipped, wont work.
please help
I jumped 4 and 8 and won't do anything..
You ever figure out the problem?
Same
Same
BTW I watched your video and performed the program in less than 4 minutes.
Villa Marina JC
Villa Marina JC
Thank you for posting this. Worked on my 99 K2500 Suburban.
I did mine using the info in this video and had no trouble. Thank you. I appreciate you sharing this valuable tip.
I just purchased a b18c5 block and I was gonna slap on a gsr head. Just like you did. You run into any Cel problems. And are you running a gsr Ecu. I'm just needing all the help I can get.
Ace Xayaphet om sorry. For not replying. Been so long. But yea. Stock gsr head will work just fine. I ran a po6 ecu chipped. Did it myself. With a map for type r.
Ace Xayaphet if u have any ? Ill be happy to hel out.. sorry again.