Відео

Awesome

Why not use spray foam in the hard to reach areas

Hello, I know your video is a couple of years old but ... did you ever upgrade the motor/esc to the Spectrum 4000kv system? If so, did you change your gearing? I would like to upgrade my RB10. I like the buggy but it's woefully underpowered. Thanks for your review!

Why did you not just run 3s instead change motor

🤣🤣🤣🤣 I had same problem with pinion easy way take out heat up grub screw with solder while pushing pinion out with tea spoon

Hey, what about the following videos about the uograde of the RB10. Will you post one ? Thanks

I ran losi, mine I soaked and cleaned with motor spray, and I ran them dry. Clean after every weekend or the next. Worked great

PRO TIP: Heat your pinion gear slightly with a lighter to soften the thread lock compound and use a QUALITY hex driver and the set screw will come loose with ease. I use MIP drivers exclusively.

I dig the motor! Imma have to look into that!

Hi Jordan, I sold you the two tmaxx trucks for the RB 10 team associated. Just wondering what I have to have the settings on for the charger to charge the Lipo

Nice. what oil in the shock absorbers please ?

A-arms are found on IFS suspensions only. Those are called links and you have upper and lower links.

What model body is that? What is the scale? Ive been wanting to build one

That thing is sickkk

Awesome build you can definitely tell you took the time and did it right. Very impressive.

Can u tell me exactly the parts number for the bearings on Amazon thanks

Haven't considered one of the aluminum trannys, but if one were to buy one of those, and find that the case mating surfaces didn't match up, I thought of two possible fixes, then discarded the first one. First I thought that a little sanding action with some fine grit wet/dry sandpaper, and just disassemble the cases, put the mating surfaces down, and massage them around a bit with the paper on a hard surface to ensure consistent material removal. But then I thought that might interfere with the gear clearances inside the case, and it might pinch a gear or gear hub. Then I thought of the old mechanics standby... RTV Black silicone gasket maker. Just a very thin layer (but not too thin) spread onto one of the mating surfaces, assemble the case and torque until the silicone JUST starts to squeeze out around the periphery, leave it overnight to allow silicone to fully cure, then finish torquing the case halves together and install. Of course, don't UNDER torque during initial assembly, leaving a bead of silicone to harden into a gasket that will be too thick and never compress enough for proper clearances inside the case, and everything inside is rattling around. But I agree, production quality from the aftermarket community for these models has been pathetically poor. While I'm pleased with the wide variety of aftermarket parts, many of these parts are not designed well in the first place, and the pisspoor production quality assurance practices exacerbate those problems. I have found that often, especially with many of the aftermarket lighting options, you really have to have your model builder skills AND problem solving skills up to par to make many of these items work and work correctly, but when you can get them there, you can often achieve some great results. Just don't expect bolt on performance out of the box.

i used the model kit that has the snow plow one, and i started with a deadbolt chassis and then put the c10 rear links in it to shorten it up, then the wheel wells line right up perfect with those parts, wish i could add a photo to the comment section, i found some small metal wheels that looks like almost old rally wheels and put the smallest rubber i could fit on them. it looks really nice and scale shrunk down like that

Where did you find that chevy hard body?? Looks good 👍

Very nice. I wish I could find a hardbody in our country as well.

nice video! keep going!

awesome video!

NICE VID MAN !

What is this song in the background? It sounds fire 🔥.

May have to bind it again or get a better transmitter I upgraded mine , but I use mine for clay .

I’d just get the xr10 just stock and the reedy S plus 13.5 motor

Do you think a b6 chassi/transmission (can be .2 .3 or .4) could work In converting this car to mid motor

🔥

48 pitch spur probably 81t, stay away from spektrum. The rb 10 has b5 style parts, b4 style chassis. Info fyi inline your electronics run shorty to front install rear tow brace to hold batt to front...for racing...

Almost 11 minutes of video for 3 minutes of information!!!!!!!!

After a unpainted body for one of these - could you tell me what replacement body will fit this model? Great video BTW.

😎 🅿🆁🅾🅼🅾🆂🅼

I won ! What is the best way to contact you privately. You did not do to bad with my last name. Lol

Several trips to the track. I have had no major issues. I am certain the stock servo won't last long

I have the rc10 b.4 and b5 and b6 I need one for my collection I race all my buggies I'm a big fan of rear motor buggies

Have you had any issues with your shocks? I've had 2 kits and both leaked right out of the box

Hello, saw you were selling your blue square body scx24. That truck has a lot of potential and i enjoyed the build. I also originally found your channel from the Facebook ads. I hope this means a new build is coming!

Just got my RB10. I had the same issue with the left front wheel. Ordered up a new set of wheels and it corrected the issue. Love the car. Really handles well !

How much would that build be rtr

Great job bro 👍🏽👊🏾✌🏽🔥

That looks really good man! Body fits size wise very good! Did you get a chance to send out that buggy? Haven’t seen it in the mail yet

Cool hard body! It looks great👍👍👍

Me likey likey

Dam that’s looks good

Nice

Lookin good!

Looks great Love to win the giveaway on it ..if it's legit.. Thank you 💓

Nice truck, and video. i have the same model kit for scx24 and i ended up using a piece paper clip that i bent for the mirrors, it is way stronger and if you use hot glue to attach the mirrors to the truck, the mirror is able to swivel and not break.... just a tip for ya ;)

Hi, thanks for your review, we keep making Radiolink better and more fun to use.

damm bro i got my headphones and youtube volume all the way up and this shit blew my ears out