Відео

ШВП вышли из строя буквально через 3 месяца.. трижды подумайте прежде чем покупать, при этом ШВП мы закачивали смазкой каждую смену. лучше купить корейские станки, дороже, но не из гавна хотя бы

Hay curso , training.?

Thanks for a great video. I recently purchased a Neoden 4 (used) and have found the tutorial essential viewing in getting the machine set up & running nicely. I have a couple of questions though : A) In the video you align each component (board component position center) - why is this necessary? Surely, if there are reference fiducials, the machine should (after locating them on the board and calculating offsets for board position and rotation) place the components in the correct place based on the pick and place file data ( which includes the location of the fiducials) ? It's very time consuming (and essentially less accurate) to go and visually select the center of each component on a board. Also, If you need to correct the center point of a component after doing a manufacturing run, it's seems hard to get the same reference points (used the first time going through visual component centering) so you have to do it all again. Or perhaps I'm missing something? B) I have a question about the 'Footprint Library' for the up-looking camera. My machine came with a smallish list of common components to select from (normal R's & C's, SOP8's etc) and they are all good, but my question is that while defining a new footprint you can only define a rectangular shape and height so how do you handle non-rectangular/square parts? For example, I've had trouble with SOT223's - while most of the time it gets these correct with a rectangular footprint definition, about 30% of the time it will pick them reasonably straight but then give them an incorrect rotation for placement. As a result I've had to turn vision correction off for these. Overall I'm very pleased with the machine's capabilities. Thanks in advance. Ewan J. Wordsworth Microbee Technology

Hello how can i contact with you

The guy applying the solder by hand on the stencil looked like he was buttering toast. Worst technique possible.

Hi need your SEO for video.

We are trying to use a device with pads that are under the body but the pads stop short of the devices outline. The 4 C sometimes identifies the body outline but sometimes identifies the edges of the pads. Has anyone got insight into the parameters that would make visual recognition consistent

We can’t get our k1830 working! It’s saying head isn’t in a safe location. It will do everything but move the head. We tried removing all feeders as the distributor said it was the component detection laser picking something up??

I am a professional digital marketing. UA-cam video content is good. But there is less subscriber. Views, seo.and tag. If you can hire me.I will solve that. If you need me.kindly knock me.

It's very interesting😊

is there a course to train on using it. for dummies ofcourse

Very good explanation...

Dear sir, I am a digital marketer, I know you have a small UA-cam channel, I can help you with SEO and monetization on your UA-cam channel.

Hi! I saw your youtube channel your didn't SEO youtube videos and also your youtube channel not monetization so I want to help monetize your youtube channel and videos SEO.

Your channel content is really good. But do you know why you can't increase your subscribers and video views despite having such good content? Because of some major issues of your channel like 1. Video SEO 2. Attractive Thumbnails 3. SEO-related video titles 4. Channel Keyword These three things are very important to grow a UA-cam channel. If you are good at these three things then you can grow your UA-cam channel very quickly. I increased my UA-cam subscribers and video views overnight using this process.

Why do these videos never have the details the consumer is actually interested in. How many feeders does this thing have, number of different size components it accommodates , working speed, cost, etc.

Kender dsv mange der er yderst utilfreds med service fra dem, feks at kunne købe reservedele til dem. Hjælp med problemer med dem osv osv. Desuden er der nyt software på dem, som IKKE er kompatibel med de ældre maskiner, selv om de er i samme serie.

is NEODEN chinese company?

47:51 R14 Missing / C4 Crooked / R13 Only touching one pad / Also a component on the very top left is missing... Also my guy went a bit excess on the solder paste application to give a "best case" demo of this machine.

Which feature of the YY1 is most exciting to you??

Check out our overview of the new YY1: ua-cam.com/video/25PN_0McFA8/v-deo.html

There seem to be a lot of plastic parts of the machine made by 3D printing, is that intentional? Is it just an early prototype part or will it be applied to the final product as well?

Interesting. You have my attention if this could fill the PNP 1 board to 100 at a good price point

Nice,expecting the review and more😁

What could YOU use an ND9 for?

What does your ideal space for SMT projects look like?

Were you at NAMM 2022? Is there an industry you’re familiar with that you’ve seen revolutionized by SMT? Tell us about it!

thanks a lot I'm from Iran and I'm very keen to establish a workshop for smd assembly This tutorial was very helpful Thank you again.

Eu fico muito feliz com o sorriso de quem faz empreendimento

Hi, We just purchased a NeoDen4 which arrived on Monday. I have been setting the machine up and initially it worked well, but we have started to notice some errors in its operation. All the problems are with the head operation. 1) Sometimes the downwards facing camera takes a “black” photo (i.e. no image). 2) Sometimes the pick nozzle does not respond. It sometimes is held down and can only be released by turning off the machine. Other times, it does not drop down even when using the manual test mode. 3) Sometimes the downward facing camera flash does not turn off. The flash remains on continually. The other parts of the machine (feeders, peelers, XY movement, rail control, upwards facing camera) all work without issue. Any ideas? It feels like a software/driver bug because sometimes the test buttons in the “manual test“ tab work then just randomly stop working. Phil

I have a Neoden IN6, but the settings menu confuse me a little bit. How can I set the temperatures in the six zones. For instance, zones 1 and 2 must have the same temperatures as you shown on video? And zone 3 equal to zone 4; and zone 5 equal to zone 6? Thanks for the excellet video!

8:20 -- In addition to the obvious color difference, it should also be noticed that on a board that doesn't reach the specified temperature, you may notice that the parts aren't completely embedded in the solder

Another great video! Is there any way to get the feeders to “blow” to release components? There are a few tricky components (specifically LEDs) that sometimes will never place, no matter how long the “place delay” is. Under the “manual test” tab, there is an option to “Blow”, but it doesn’t seem like this functionality is possible during run time. When manually picking the component and then enabling “blow”, the components fall off like I’d expect. Without “blow”, the parts can sometimes take 1-2 minutes to fall off the nozzles on their own.

Excellent video! Do you have any pointers on how to get components to “snap” into place? When I reflow boards by hand with a heat gun, they tend to “snap” in place, even if they were slightly crooked. With the IN6 reflow oven, they tend to solidify in place, which is pretty annoying if something like a microcontroller is slightly crooked.

Can you send me price detail and some technical specification

Sar I want to purchase this machine for our LED production

Why does your software have a button that changes the interface to Chinese and (here's the stinker!) requires a PASSWORD from SUPPORT to get back to English!?!?!? Who designs in traps like this????

I am aiming to buy something like this in 6-12 months from now. Does your company offer in person demos before purchasing? I am within an hour from Ringwood, NJ so it would be easy for me.

What is cph and total cost.and also share details which type of components are mounted

I want to visit ur factory

Nice

I did everything you did for the special feeders and everything works but the machine only picks parts from the first column. It won’t pick parts down the line

C4 is rotated :) :-(

We talk with our arms..

Are you engeneer of neodentech?

Great video!

I am the engineer att neo den tech

I see there's a compressor to the side at the end... i thought it had one built in?

vibration feeder , you are not cutting the end of tubes ? good luck

Where is the software for neoden 4? I bought a new device and I don't know how to program it. Can you send me a software link?