The LS Shed
The LS Shed
  • 30
  • 40 183
1968 Chevelle, Tanks Inc EFI tank
Installing a Tanks Inc EFI Fuel tank, using the CPP pump hangar…same as Tanks Inc unit without their pump.
Переглядів: 489

Відео

Finishing Up The Transmission Cross Member!
Переглядів 201Рік тому
Finishing Up The Transmission Cross Member!
1968 Chevelle Cross Member Fabrication
Переглядів 62Рік тому
1968 Chevelle Cross Member Fabrication
Automatic Solenoid Valve on Shop Air Compressor
Переглядів 1782 роки тому
I realized I had a half inch ball valve on my compressor outlet. I need 3/4” all the way to my sandblaster for it to work. Also, I forget my air valve on all the time, small leaks in the shop cause it to run more then it needs to, which in turn makes me have to service my dryers more often. And, it’s a pain to use my outside air if I need to fill a tire. So this video is my solution. Motorized ...
5.3 with Sloppy Stage Two on runstand, startup with no tuning. SS2
Переглядів 2,2 тис.2 роки тому
Runstand made of pallet racking, and leftover parts. Made it five years ago for the 5.3 swap in my CJ7, added a radiator and exhaust so I can warm up the motor and go closed loop. Running with a harness direct from China. LS6 manifold pretty much triples the cost of the engine. Running with only VATS and rear O2s removed in PCM.
1971 C10 Build First Day, LS , Porterbuilt
Переглядів 2124 роки тому
Taking apart a new project, 71 shortbed C10
F350
Переглядів 556 років тому
F350
Jeep CJ-7 Part two, 5.3 Swap, LS swap
Переглядів 20 тис.7 років тому
5.3, and Ford T18 swap into 85' CJ-7
Jeep CJ-7, Part 1, Initial upgrades, OME springs, Metal Cloak
Переглядів 1,4 тис.7 років тому
Most of this work was done in early 2016, I don't like to do too much work on project cars during the summer when I'd rather enjoy things, so these initial upgrades were how I drove the Jeep over the summer the summer of 2016. Every time I drove it with the stock 258 and T5 transmission I thought about doing an engine/trans swap. See part 2 (coming) for that.
First drive Jeep CJ with 5.3
Переглядів 3197 років тому
Still had lots of stuff to finish up but it was running and somewhat drivable so I took it for a little drive around the shop.
5.3, LM7 running in Jeep CJ7 for first time
Переглядів 7387 років тому
Got the exhaust and fuel system in so this was the first time running the engine on the Jeep frame. Testing out in tank fuel pump which was nothing more then a stock Tahoe pump coupled onto the stock Jeep sending unit simply by cutting the pickup tube back and attaching the pump with a piece of high pressure hose and clamps. I also used one of the Tank vent lines as my return because they're la...
5.3 in Jeep CJ 7, before first start
Переглядів 1357 років тому
engine mounted exhaust done, fuel system ran, using stock Tahoe pump coupled to stock jeep sending unit.
Torque Cut 22 Machining Center
Переглядів 1847 років тому
Torque Cut 22 Machining Center
February 25, 2017, last time running the Jeep with the 258, LS swap on the way.
Переглядів 727 років тому
I made this video to show the original 258 running before the LS swap, so I could sell it down the road, ended up getting $500 bucks for it, same as I paid for the 5.3...
5.3 dying with throttle 2
Переглядів 1157 років тому
5.3 dying with throttle 2
5.3 on stand, dying
Переглядів 2147 років тому
5.3 on stand, dying
2002 Nissan m40d
Переглядів 1,9 тис.8 років тому
2002 Nissan m40d
20140824 131138
Переглядів 1710 років тому
20140824 131138
1976 Kawasaki KZ900
Переглядів 78912 років тому
1976 Kawasaki KZ900
Dave Driving his Baha on the Chain
Переглядів 1912 років тому
Dave Driving his Baha on the Chain
Racine Boating on Lake Michigan
Переглядів 12012 років тому
Racine Boating on Lake Michigan
Racine Wisconsin Boating Chris Craft Commander 333, North of Racine
Переглядів 88112 років тому
Racine Wisconsin Boating Chris Craft Commander 333, North of Racine
hydrostream 023.mpg
Переглядів 2,6 тис.14 років тому
hydrostream 023.mpg