Відео

@@harrydoherty8299 That sounds like a sweet setup! I’be been trying to find a really good miter for the table saw. What brand did you get?

@@kubanito3776 there are multiple blend doors, you need to listen to make sure you’re changing the right one. If there is a knocking noise, and the problem is either with the door itself or the door actuator. 99% of the time it’s the actuator. Sometimes the henges on the blend doors break, but that is very rare

@@shawneggsware9672 what?

Thanks man, it’s definitely unique, and it’s trying to tackle a problem that I haven’t seen any other brand try and tackle

Awesome! Glad I could help

I would argue that thousands of people have said the complete opposite, but I have some more tips for you if you need some help. These are just to 2 most common issuses

@@FixItFrench def not the same… but yea I replaced hole faucet, and the hot water valve faucet below sink. I Have hot water pressure n restroom. But barely any in kitchen, and hot water pipe n valve faucet jolt when I use washer. Front yard faucet spurt when it’s open as well.

@@rachelbarron5642 This is very common after replacing a faucet and valve. Especially with the hot water. What that means is debris from your water heater/tank came up through the water lines. Here are the 3 things I would clean out 1. Aerator 2. Hot water line (As shown in video) 3. Mixer screen found in the hot water handle Each handle should have a small hole that has an Allen head screw in it. Remove that and you can remove the handle. Inside should be a small mixer screen that gets debris as well. If that doesn’t help, you may need to remove the faucet and force water (or air) into the spout to push out any stuck debris. Hope this helps 👍🏼

Thanks buddy! It definitely took awhile, but it turned out fine

I agree, it’s a pretty handy tool, and thank you for the feedback! I am testing out a new microphone in this video, so I’m thankful to get some feedback on that. I’ll look into and try to improve the sound next video

Very unique! I hate charging 3-4 batteries at the end of the day and having to mess with the bulky chargers and tangled cords

If you look on any battery it actually tells you which connection is positive and which is negative. Most of them are in the same spot, but some are different

@@FixItFrench i know but you can easily make an error, If you are a bit too tired or something 😉

All batteries including the Milwaukee have positive and negative pins. If you look closely on the batteries you will see that. The instructions are clear on how to use the pins correctly. I’ve only been using the charger for about 3 weeks, but it has successfully charge every battery with zero problems

I think so too! I also think charging batteries is a problem that not very many companies have tried to fix

I guess time will tell him that. I have not noticed any difference in the quality of battery. I use both Milwaukee and the wall. Also, at the end of the video I share charging speed times that I tested personally. The charging time wasn’t much different between the regular charger and this charger.

Appreciate the find but your review was a little lacking. Eg- from Amazon link for product "Charging capacity: 3,000mAh total". Yet the picture for the product shows 4.0ah (4,000mAh) for at least 2 batteries. Does this mean that a 5.0ah battery will only charge to just over half capacity? Either way, I do appreciate the find and the product idea is brilliant.

@@sogbryan6633 Excellent question, I wondered the same thing. A 3 amp charger is capable of charging a 4 amp (or higher) battery. I used a Milwaukee 5ah battery in this video and it charged my battery to full charge. It took about 5 minutes longer to charge my 5ah and about 3 minutes longer to charge my 4ah. The higher the amp, the longer this charger will take to charge the battery. I hope that helps

@@RichS-ki9xf that sounds like the blend doors aren’t cooperating. Very hard to say why that code came up, but it could be caused by the doors malfunctioning. Sometimes 1 electrical problem can cause others as well

@@arronbarnes1755 I would love use a CNC, but I currently do not own one. I use jigsaw and a scroll saw to make these. Thanks for watching

@@kylegauths4718 awesome!! So glad I could help!

@@RibbonsPink I appreciate the feedback, and I still use this planer on a daily basis. I even use it with live edge I get from the woods. It’s a great planer. Overall I would tell you the 735 is a better planer, but the Hercules is a beast, with a lot of features, and will give you great cuts. Hope this helps 🤙🏼

@@jondorr4011 I’ll try and find a video that will help. I don’t personally have a video, but it shouldn’t be too difficult. Before you start, make sure you remove the negative terminal from the battery.

@@FixItFrench Much appreciated, I have to replace mine and no one at AutoZone or O'Reilly's could understand what part I'm looking for or if the one I got would work

@@jondorr4011 ua-cam.com/users/shortsKRrn-Z5egLk?si=n1pqJqjBQS7SjMoH You may have to copy and paste that for it to work. I could find a video of people replacing the whole harness, but this videos shows how it works. You just need a longer harness. Hope this helps 👍🏼

@@TheJachinbankes Did you reset the HVac system by removing the hvac fuse? I tell how to do that at the end of the video. If that doesn’t help, give me a little more description of what’s happening

@@FixItFrench i was have the same issue wen i press recirculation button its start hit like in the vid, but its stop and now the recirculation doesnt work, wat can i do?

@@joynerlever7635 Is the recirculation the only thing not working?

Thanks brother!

Thank you, hopefully it helps someone

@@FixItFrench It will for sure!

I’m not sure where you got the idea that this is how it works. The debris comes from the water heater. I have other tricks that can help with your low pressure. Very seldom is the problem a city problem. Is the low pressure problem throughout the whole house, or is it just a certain room?

@@karan4251 awesome! So glad I could help

@@brindasembaiyan1855 awesome! I’m glad I could help 👍🏼

Thank you! I have made these jewelry cabinets several times. This is the first time I’ve made the rotating earring display.

Thanks, brother! The jewelry cabinet is one of my best sellers

@@FixItFrench I can see why. People should buy two. One for themselves and one for a gift. 👍

@@inspiringbuilds lol that sounds nice to me!

@@sandorlaszlo4553 love to hear it! Glad I could help 🤙🏼🤙🏼

Awesome!! Glad I could help

Awesome! Glad I could help 👍🏼

@@Newyork8608 This process will also work for the cold water! That noise most likely is from a small clog

@@scottbruzik9837 thanks brother! My parents were very thankful for these doors, and they’re still standing strong 🤙🏼🤙🏼

Love to hear that! 👍🏼👍🏼

@@bubbaewack5503 The blend door is used to determine which air blows out of your vents. There are always other causes for your HVAC system to act up, but the blend door actuators are the most common problem. If you hear a knocking noise, you can pretty much guarantee the actuators are bad

Thanks, brother! I had a lot of fun making it. Haven’t seen you post anything in a while, have you went on any adventures lately?

@@yeehaw779 you have the 2.4 L. This car is a 1.6 L there are very few differences in vehicles, but yours has the filter on the bottom of the car. Also, when you remove the filter, all the oil in the tank will drain so, you need to change the filter when you change the oil

@FixItFrench my car is the 2018 equinox and it says it's a 1.5L?

@@yeehaw779 gotcha the 2018-2023 are a little different than the 2010-2017. The car in this vehicle is a 2017 and it’s a 1.6L I guess the 2018-2023 changed their location of the filter

@@carlfagen3935 satisfaction guaranteed lol

@@stevesiefken2696 it does eject the saw dust, but if your talking about the technology that the 735 has, I don’t believe any planer except the 735 has it. Hope that helps

@@lordplague420 I would repeat the process, and check the aerator again. How old is your faucet?

@@FixItFrench the faucet doesn't have an aerator and I'm not entirely sure how old it is, I rent an apartment and just didn't want to deal with management 💀 definitely several years

Well tell her I said: Amen momma! Lol Glad I could help brother 🤙🏼🤙🏼

Agreed!

@@YellowJacketGarage thanks brother! I love making fun stuff like this for my nephews. I also made some scavenger hunts, and escape room. I’ve been thinking about trying some of that content out as well

@FixItFrench bring it, your content is always so well done!

@@arronbarnes1755 I do that sometimes also. My chisels are sharp enough that you don’t have to, though. They will cut the wood, even if it’s not clamped down👍🏼

@@inspiringbuilds thanks brother