- 131
- 290 209
The EK4R guy
New Zealand
Приєднався 31 січ 2012
This channel was created purely & solely for the love of my EK4 civic but recently have gone out of my comfort zone by playing around with Mopeds/Scooters experimenting with engine swaps, mods etc etc
Alot of budget backyard out of my garage DiY stuff posted here so if you into that stay tuned and welcome!!
Alot of budget backyard out of my garage DiY stuff posted here so if you into that stay tuned and welcome!!
DIY Honda civic window regulator fix
Decided to tackle & fix the stuck window regulator which turned out to be not that difficult and once everything was cleaned a re greased worked 100%
Переглядів: 27
Відео
Fuel pump install on my civic
Переглядів 123Місяць тому
Installing a Walbro 255L/hr in-tank filter in my civic, I know I’m not gona be near 500hp but would rather future proof it now especially when about to hit dyno soon. I will be hard wiring it to consistent 12v with a relay & switch setup.
Toyota Prius blocked EGR | Oil catch can install
Переглядів 1392 місяці тому
I’ve owned this Prius for almost 2 years now and within the 1st week it suddenly hesitated slightly at low speeds and low rpm’s gradually over the course 2 weeks after noticing, it got worst to a point where it started to vibrate. So I decided to clean all EGR related ports, tube and hoses etc (not the cooler & valve) along with intake manifold, throttle body & injectors. I also managed to clea...
Toyota Corolla CAT delete
Переглядів 752 місяці тому
Decided to remove the Catalytic converter on my RunX and also a last minute tail pipe with the excess pipe. I was amazed at how easy the complete exhaust system unbolted without stripping a single bolt!! The CAT was extremely clean and not clogged at all which was good to know. I was hoping for a much more deeper tone but got surprised at how it hasn’t changed much, because everything went so s...
Toyota Prius oil change
Переглядів 532 місяці тому
Oil change on the daily driven work horse. I will compile a video of the OCC setup.
Testing continues on the civic
Переглядів 362 місяці тому
Testing continues on the civic making sure we DYNO ready!!! EXHAUST. Good to see the exhaust system is working as it should apart from the pin hole leak that needs to be welded and axle back pipe touching the rear sway bar. FUEL SYSTEM The fuel system seem to be holding pressure and no leaks!! COOLANT I did notice coolant dripping from the overflow after the test drive which is abit of a concer...
DiY Exhaust system for the civic V2 | FINAL!!
Переглядів 562 місяці тому
DISCLAIMER I'm no welder nor a fabricator I do this shit as a hobby, ima fuck around & find out kinda guy so if it works for me l'm happy. So my GoPro malfunctioned and I lost all footage of me completing the Axle back and muffler but oh well I've managed to compile something for you guys from what I had.... I've finally built my own custom exhaust!! A lot of hours, wastage and lessons learnt f...
DiY Exhaust system for the civic V2 | Part 3
Переглядів 322 місяці тому
I'm not a welder nor a fabricator do not replicate what you see I fuck around and find out and do this shit as a hobby. Pretty stoked how well this version of the exhaust is turning out just goes to show how well something can turn out by taking your time and not rushing yeah it looks like shit but it works and it’s leak proof!! Exhaust bracket all tacked up which came out really well making th...
DiY Exhaust system for the civic V2 | Part 2
Переглядів 453 місяці тому
*Disclaimer* I’m not a welder nor a fabricator do not replicate what you see I fuck around and find out and do this shit as a hobby. In this part I get to fab up some diy exhaust pie cuts to attach onto the Reso which is needed to align the pipe straight in the tunnel and oem hanger points. The main goal is have the pipe tucked as far up as possible without putting too much stress onto the flex...
Diy Exhaust system for the civic V2 l Part 1
Переглядів 2,2 тис.3 місяці тому
Disclaimer I’m not a welder nor a fabricator do not replicate what you see I fuck around and find out and do this shit as a hobby. This is one of those jobs that you don’t really wanna re visit but due to me rushing the process I fucked up a lot of things let alone over looking the basics In the 1st attempt I messed up a complete V band set, never installed a flexi, rushed with the welding caus...
Test drive time!!
Переглядів 1,6 тис.3 місяці тому
Due to the car not being road registered some parts of the video is blurred out First proper test drive went really well but due to the exhaust system being so loud and to keep the peace with my neighbours I had to cut it short!!! However it was good to test out few components in that same time i.e. the wiring, clutch, gearbox, IM & TB and man this thing is touchy and very responsive 🤙🏽 Few fin...
Working on the civic’s cooling system l final
Переглядів 743 місяці тому
Working on the civic’s cooling system l final
Working on the civic’s cooling system l part 2
Переглядів 274 місяці тому
Working on the civic’s cooling system l part 2
Working on the civic’s cooling system l part 1
Переглядів 1724 місяці тому
Working on the civic’s cooling system l part 1
Looking for vacuum leaks on the civic
Переглядів 858 місяців тому
Looking for vacuum leaks on the civic
Working on the civic l motor prep l wiring harness l
Переглядів 110Рік тому
Working on the civic l motor prep l wiring harness l
GY6 80cc big bore kit top speed l part 2
Переглядів 358Рік тому
GY6 80cc big bore kit top speed l part 2
Repair and painting the Moped I part 2 (final)
Переглядів 52Рік тому
Repair and painting the Moped I part 2 (final)
Building a GY6 50cc motor on a budget with budget mods l Part 5 ll FINAL
Переглядів 137Рік тому
Building a GY6 50cc motor on a budget with budget mods l Part 5 ll FINAL
Building a GY6 50cc motor on a budget with budget mods l Part 4
Переглядів 131Рік тому
Building a GY6 50cc motor on a budget with budget mods l Part 4
Building a GY6 50cc motor on a budget with budget mods l Part 3
Переглядів 116Рік тому
Building a GY6 50cc motor on a budget with budget mods l Part 3
Building a GY6 50cc motor on a budget with budget mods l Part 2
Переглядів 114Рік тому
Building a GY6 50cc motor on a budget with budget mods l Part 2
Building a GY6 50cc motor on a budget with budget mods l Part 1
Переглядів 198Рік тому
Building a GY6 50cc motor on a budget with budget mods l Part 1
Это частичная замена, или полная????
Best crossover I’ve heard for a b16
What are you using for a degreaser?
Just regular work shop de greaser, however do not inhale.
If thise is for automatic trany? Y thy are put in picture that Do not use for automatic transmission
Best Video Ever
good video, I just ask you what type of cable did you use, 14AWG or 16AWG or 12AWG ?
Stock ecu?
need help kinda cofuse what fluid transmission gonna used? mine honda fit GD2 but the dipstick says ATF..
CVTF
Dankie maat. Love die land flag
Couldve saves soo much time by just depinning the plug lol
@AstronautRainesfair point
Sounds good
Ehy is vtec so late
Awesome video. Where did you get the boots? Thanks
crazie how you can instantly tell when vtec in on mode.
Haw mich litra gou in variator? Pliz
hello i need a semi axle like this for my 2008 honda civic hybrid!! can you give me an infprmation where i can order it
This is a great tutorial....all in fast forward 🤦
due to copyright background music i had to mute the video, a new channel intro will be uploaded soon
I like the idea of jacking up the right side of the car (I did that the first time I changed the CVTF), but I found that it got so much fluid out that the standard 3.5 L pack was not enough to properly refill it, and I had to go out and buy another 1 L pack.
That’s only obvious that the Jack is in the rear under the cover, thought you were gonna show Jack location points under the car
There's something really grating when a young women says 'I *fucked* all these guys'. Only in America
What are the 2 cables that go in the fuse box ? Need specific names cause i forgot please
starter & alternator mate
🔥🔥🔥💯💪👍🤝
Machine
ua-cam.com/video/YmFIaqzAP7Q/v-deo.html
65mph 💩
Now your glove compartment will not close
😂
It closes just fine mate
can you still actually use the glove box as if so im doing this@@EK4rguy
Never use screwed clamps. They will cause balance issues and vibrations
Good to know but never had any noticeable issues and not only do I drag race but beat on it
Whats all done to it? I'll be picking up a B18CR EK3 Vi-RS soon
Trust me you won’t regret it they go hard asf
There’s a stock b20z2 non vtec same as jdm b20b high compression running the same thing as your b18c
Fell out of vtec in 3rd? What transmission you runnin?
S80 non LSD in this clip, and we had gearbox issues hence the 3rd gear
Those engines sound sexy ASF
Can’t go wrong with ITBS
What kind of gauges are you running in the middle section? Love the white faces and orange needles
Oil temp and oil pressure, yeah they look awesome
What kind of numbers are you putting out? Streetable?
That's a fake cvtf oil
No its not. That is genuine for Japanese Domestic Market.
Have to use specific grease for axle/driveshaft/CV and NEVER use those clamps you used as they will off balance the drive shaft at higher speeds - think tyre balancing because the drive shaft spins FAST
Good job bro
It use all 3.5Litres? Chur
Cunningly measured to be exactly right for the trans being partially drained using this method.... and not tipping the car further to encourage more fluid than the 3.5l to leave the trans... which actually holds far more fluid than this "change" amount...
Hi from another kiwi nice video i'm going to do the same to my honda fit give it a cvt oil change as mind is also doing the vibration and shuddering brought my genuine honda cvt oil on trade me as well as XADO 12O Revitalizant hopefully it will eliminate the problem i was thinking of getting a toyota vitz but the honda fit has much better luggage room and seems quicker than the vitz when you compare them both.
Amigo você conseguiu resolver o problema? Pode dedicar alguns minutos em comentar como está sua experiência agora?
You can see more on INSTA: @gen54cr
Nice thanks! Just bought an 01. Took all this apart and even saw the little Golden edge of it and thought it was just part of the trunk and ours didn't have it. Great video 👍
Thanks for watching and glad the video helped you out, have a good day.
How did you get the spider out, the part that holds the 3 bearings?
Thanks for watching. That should just pop out once the boot is removed, there's no clips holding it together.
People who make instructional videos like this are actual angels, thank you so much for being so wonderful!!!
Terrible video.
Thanks for watching and your feedback.
Berapa liter kak kalau ganti gitu aja
How bad are they to drive on road ?
Holy fk that is nz🤣
Looks like nz
I think manurewa haha
Was about to say, looks like home haha
thanks for your video. There are CVT's sold in the market but not Honda brand but made in Japan. Are they reliable? CVT and CVTF are the same? How can you explain that indication that says " do not use for in automatic transmission"
conventional auto transmission use ATF (Automatic Transmission Fluid) and CVT (Continoiusly Variable Transmission) gearbox use CVTF (Continoiusly Variable Transmission Fluid) or HCF-2. ATF cannot interchange with CVTF.
Sounds like a K20....and it probably is
It's a B18c with ITB setup not a K20
sounds like a b lol
Serious? This is B
How are you gonna tell somebody else whst they have under their own car?
@@ssjdavid Exactly. Fckn Internet 🙄
Weird bro !!
Annoying as! Just don't click on them.