Відео

idea how to connect LCD ?

you are good teacher - what country ?

How to use without wireless

Share full video

for who may concern: first connect the usb then the power on relay,

RemoteXY is not seen in free version 9.2.0. Pl help, thank you.

Great effort sir!

Great effort sir, RemoteXY block is not seen in free version 9.2.0. Please help, thank you

How to calculate PF by know V Or I from VT and CT

IOS-RemoteXY Error Cannot find the IP adress of the device

Great knowledge, Thanks a lot

hello how are you It turned out great. I wanted to try it too. only i have some problems. FLPROG is not accepting code from remote XY. FLProg 8.2.3 version remote XY also at the same time I could not find the text command

Hi Onos. Which version of RemoteXY you using? I can't find "text " function on RemoteXY.

Sir im using win10 until this day , why it can't work with the ch340 nano??

Thnx. Thnx for making these videos. It is appreciated.

I have thos modules and they are unreliable to switch the load (lamp) off after it has been on for some hours. The relay is not driven correctly!

Power supply issue? pitting on the contact

Hey, How can i setup the SF of the Modul?

connect to wifi ?

Can I reach out to you personally for help?

Does it support WROOM32?

excellente vidéo est-il possible d'avoir le code sur un bloc note svp

Hi sir good morning , sir please 🙏 can you tell can we use spwm to control motor speed . please 🙏 give response.

Hi sir good morning , sir please 🙏 can you tell can we use spwm to control motor speed . please 🙏 give response.

nice video did you have more example with arduino extension ..servo motor..etc tanks

learning from your video. Hello from Singapore. And thank you sir.

Great!!!

Sir small doubt how link pwm with bluetooth module to increase or decrease dc motor speed . sir please guide me.

Hii sir , I have a project to make so can you help me for this project. If you see my comment then I will please comment back for more conversation for project .

Good efforts

very informative. thank you for sharing

thanks a lot

Very nice

This work 100% , thanks for sharing

Sir, one question. How to use multi sensor?

can i get a new link for ebyte config?

my module has a delay of 7 seconds how can i fix it(using two pcs for drone and controller 7 sec very long time)(using E32-900T30D)

Super sir thank you

i am using I/O expander PCF8574 on ESP32 how can I assign I2C PCF8574 pin as input and output in FLPROG please help me out or make a vedio

in outseal you go slow but when you came flprog you speed like you doing a kind of magic. but good sir.

What coming next?

Great!!!!😀

How can I find Arduino nano PLC board like the one you are using?

great tutorial. thank you for sharing your knowledge

please upload project link for #8 Industrial 4 20mA Modbus 7 Segment Display

Is the OpenPLC source code is free and open? if yes, please give the link please

Well done

Hi Onos: First of all, congratulations on this new Arduino series! I tried this example and works perfectly, but I have some questions for you. 1.- Is it possible to work with this ModbusRTUSlave and openPLC (Arduino extension)? If so, would you be so kind enough to make a video about this? I am asking you this because the Modbus embedded with openPLC uses a loooooooooooooot of memory. 2.- How to configure memory Modbus Bits (B1, B2…etc). Could you make a video about this? 3.- How to configure the Modbus communication ports for Arduino Mega?, I mean Tx0-Rx0; Tx1-Rx1; Tx2-Rx2; and Tx3-Rx3 Also a video would be very helpful Thank you very much in advance!😀!

nice