Відео

Looks fun

You mentioned in one of your videos that you'd love to find a skiff kit. RCB kits out of the Netherlands has them, I think they are around 229 for the full kit. I bought from them before and it wasn't bad, slightly higher for the shipping. I bought the fooling racer flat bottom short kit from them.

I just do not likew electric. Thiem to run is short even with brushless. I have nitrro and gas engines in the boats , trucks and planes. IT is 5 to 7 min for electric or 15 to 30 min for nitro and gas. No brainer for me lol.

I have what I think is an old design 3.5 I also have one with a carb butterfly , however this is just a carb wide open design and then a plate that slides in and out at the exhaust port. THis is how it regulates rpm. DO you know of these and where to find more on them? So far have not had much luck finding this one. Thanks

Flat calm water SUCKS for a flat bottom! Need a little chop. Grew up racing flat bottom real boats... lol. Outboards tho... Love them, but always wanted to deck ride in a skiff

What type of remote starter are you using ? Great Video !

Great vid mate sweat boat, love ya lake, ya lucky bugger ,when is the invite for a BBQ 😂

Good Chuck & Chat Brother. Keep the dry side up..

D*** JJ you're lake is so sweet And right behind your house.What could be better for someone that likes boats

Are all the zenoah engines thr same where the collet will attach to the motor? Ive seen a few different things on the market, but every video i see the collet is attached to the motor shaft. Ive seen clutches, ones with a belt pulley. And ones with just the collet. Whsts the best approach? Im not sure i want to use a clutch.

Boy did this video bail me out. In particular was the part about flooded engine. Purposely flood engine and did exactly what you showed and now have confidence clearing out the engine. Putting in the plug 1/3 of the way was surprising. Thanks again my friend!

I have an Ez VEE I could never get right. I used this set up and changed the prop and the boat took off. My granddaughter uses this boat and has a ball with it. She will be racing next season. Thanks for the video. 😅

Thanks so much for this video. I now have fail safe on all my boats and I know how to use it thanks to you. Great video!! You’re the MAN!

JJ what is your discord link?

I learned you absolutely can over clamp a boat and distort the chines. no bueno.

Are the engine mounting holes pre drilled on these kits?

What a dick..your a bad example of a rc hobbyist.

I need the back story to what and how they set off jj 😅😅🤣🤣

What I'd ken and Matt don't get sarcasm 🤣🤣🫡

I want the go ped. Lol

Hahaha 😂😂😂

Sweet mother of Mary JJ.....No worries i responded

Something got you all WOUND UP or BENT OUT OF SHAPE with Ken and Matt. I’m dying laughing here. My question is “What Ya On?” That’s what I want to know. LOL.

did you call us all fuck sticks??? wtf will never watch you again

You hit the nail on the head with those 2 fuckers!!!

Bro that's sweet!! Did you dip it?

Sweet ride!!

Nice Rack!

ZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZZ

Think it need a 1 / 7 32 of a turn on the high Needle jj😉😪

Do you have any setup with electric?

Try your carby setting at 2 full turns out on the low and 1 full turn out on the high

Is this an A-box or v-box? I think this is my next boat.

The best rescue boat is the one you have.

Great video as always brother! And as always learned somthing

IDK how you can make a backlash run like shit, that is a feat.

I like the step by step procedure. Helps me work out the bugs I don`t understand.

hard to beat a blazer hull , fast and sexy

Best boat review ever! I found one of these today for $75. I might still buy it even after this glowing review

time for another upload

I have 29cc zenoah marine engine, but unable to run 😢, pls give some tips

Runs nice and looks good too👍

Great vid mate ,ya have a nice spot there mate ,love ya collection of boats hey ,look forward to seeing more uploads ,thanks 🤙🤙🤙🤙

Nice run brother! Looking forward to the chuck n chat

That's too bad indeed, JJ... But I hope you can fix it! Stay safe there with your family! 🖖😊

I'll give you $35 for that cylinder and piston recoup some cost.

Well hell JJ....Get er ripping brother.

if only the piston is scored and not the cylinder is should be fine with just a new ring. tight spot is just flywheel magnets. I think you're good to go.

Are you sure you’re not feeling the magnetic pull of the flywheel on the coil at the end? Looks like the piston is just before tdc, so my guess is it’s just the flywheel magnet

That sucks, wanna see that thing cooking!