Відео

I want to increase the delay time and for this i have replace 100uf capacitor with 330uf capacitor but relay doesnt work. when i insert 100uf back then again its starts working 10sec , Whats wrong can you please tell me i need 20+ second delay

$8 for shipping and 23 for the relay? No way.

Price

Can i use this for milliseconds?

Great video, I want to delay the relay to trigger after receiving a signal but stay triggered until signal disappears, Can this be done?

Is it work for 6 VDC and 4 Amp source?

I have 4 five pin 12 volt DC relays hooked together along with two limit switches and a push button momentary switch that runs a motor. I push the momentary switch that starts the motor moving an arm off the first limit switch then goes to the second limit switch and immediately reverses the motor to make the arm go back to the first limit switch and stop. I need the motor to stop for about two seconds when the arm hits the second reversing limit switch then the arm needs to travel back to the first limit switch and stop. Can you tell me what kind of time delay relay to use? I need help to know how to build this circuit I am not very knowledgeable about electronics.

this is good modul but need change with big relay for reduce damage modul

How to use the rear camera when it is in D mode sony axv ax8000

People have no pride any more this is something that can be soldered together from a few parts why buy from china ! use your Brain !

Hi, can this be used to delay the dome light of a car? and will it turn off if the key is turned to ignition?

220v motion sensor and N555 module, DIAGRAM

Hello, may I use it to control the glow plugs of the diesel engine instead of the timer / controller

I need one relay 12v 20A 5 second duration adjustable do you know any recommendation

Wouldve been helpful to see the whole wiring diagram

H ey Danny Iam locking for a circuit diagram for the Timerprint QF1021A/B V1.5a thanks Hermann

I wanna a closed relay,when signal come it open with delay and close the power to source But when the trigger signal stop, is it closed immediately or have delay ?

Will bridging the trigger in cycle mode will cause it to cycle constantly on power on?

How does one adjust the Left to Right viewing angle? I'd like for the display to be angled toward the driver, not the middle of the car...

I have this unit, it has paid for itself to put it mildly. For a female that is saying something.

Cool component.

Mereko 5 nomodyul chahiye kitne ru mileg

Nice.

Good info.

Cool component.

Nothing up thanks.

Would the bu509 be able to be used as a turn signal flasher?

Is there a version where the 86 and 85 are flipped. I would like to use this as a modified led flasher but my car ground is on the left side and trigger on the right side

What type of relay do i need to make (Follow Me Home Headlights) i need a relay which will receive the signal from the door being locked/unlocked and can stay on for about 10 seconds which can signal the headlights relay switch to turn the headlights on

Is it suitable for chevrolet Spark car? It's coming with dual din..Ax8000 can be fitted in dual din? SPARK

Hi running puddle lights using foot well lights to trigger. Is this correct. One to either wire to Tigger the unit.

So I went to purchase this...put in my payment information then went to 404 page not found. I cannot get to we website on any devices. Seems like a scam link to get card info. Any ideas?

this is misleading. the device is not 'latched' is it self powered, so it is parasitic. a 'latched' relay is like a ball-point pen. on push and it will change state with no power. a true latched relay can put in one state and will remain that way, without power, indefinably. a true latched relay will not consume any power, except for the momentary toggle between states.

This circuit Can i operat 24v input

i need a relay pcb that can read a pulse and latch on till i push the reset button ...basically i need it to do nothing till it sees pulsing and instead of pulsing the relay it latches it till i reset it with a switch

I want it to keep my power windows powered for 30 seconds after i take out the ignition. I have power to 30, ignition to 86, ground to 85 and 87 to the power windows, but the relay turns off immediately, even with max adjustment on top. Any clues??

Will it remain latched when there is no power to the board ❔

So if I want my radio in my 2013 toyota camry to stay on for longer, I would buy one of these ?

On a close signal, I need this to turn on/off in 0.5 second sessions. Can I get it that fast or faster?

Ser tel me this is adjust for 1 hour

this video answered all my questions.

Does this relay drain the power when the signal is not turned on?

Can 12v relay work with 18.5v dc input voltage?

Mine didnt come with brackets. There is nothing to mount the radio to.

Does that company make a relay that when it sees power it will only stay on a set period of time before shutting off even if it maintains power? Project I am working on I am trying to add a "wait to start" light but I need it where when the key is turned on it will power up the relay for 2 to 3 seconds then switch off. Only other option is to jumper off the seat belt light but I dont want to do that unless I absolutely have to.

Hi is this compatible with use of a 12v fuel priming system

so if you wire them together you get a timed switch?

Will this unit be able to be used fr a turn signals on a home made trike that I'm wiring up

How much sir

is 0,2 sec exact posible