Відео

Can you help me my speedometer stopped working

You're great i fixed allot on my bantam it's my first time. Im just struggling with the speed sensor,to get the white piece out

You are very helpful thank you I'm looking for the speed sensor location on my bantam rocam

Sounds like you’re on daddy duty as well 😊

What brand are these red screw drivers have been using them forever the white brand mark rubbed off long ago but still in good condition very common in south africa and zim with the transperant red handles and black tips

Синий выдерживает большую нагрузку чем красный,видно по длине ключей

Thank you so much Jaco I had no one to teach me how to do a proper installation, now I just did managed to install a new Clutch kit, thank you once again, From Bloemfontein

Thanks for this video! Helped a lot. Was a bit worried as my clutch finally went after 340k km on my 1.6 XLT. Removal was easy. Installation of gearbox was terrible😂, no space to pick up box and little to no room where the diff sits next to the subframe. Never doing this in my driveway again.😂

Thank you for the video it is very helpful, just a quick question how far deep do you hammer the bearing outer rings?

Great Job!

I have the problem with my car Roy cap does not start

Baie dankie vir die video, ek is nuut met die rocam motors so nou weet ek min of meer waar om te begin as ek timing chain moet doen. Ek sal ook twee gate boor deur die bellhousing om by die sump boute uit te kom, ek moes dit ook doen op my mazda

Great vid. You'll be surprised how many people get it wrong on these vehicles

Please I need advice. I change timing chain from my bantam 1.3 rocam now the plug number 1and 4 is firing. What can cause of that

Hi,my bantam start getting me trouble a month ago.i drien the oil to give it a surface then i release there is petrol in oil because the was very thin like tinners.w hat can be problem

Bro are suzuki swift rotor and suzuki dzire rotor interchangeable or compatible?

What oil used for gearbox?

Can you use paper towel

I have my bakkie for 12 years and I never knew the oil needs to come off for oil pump.. Honestly this bakkie has been a bit of a headache to work on geez.. Worst bit of engineering from Ford and I love this bakkie but Ford nee fock man

jb is it possible modify ford bantum rocam injector into carberator

Do it… make it nice!!!

Naand Jaco, dankie vir die deel van die saag. Ek's mal oor die ou gereedskap en doen ook my eie dinge van die huis af as ek nie werk nie. Ek dink dit sal 'n baie goeie idee wees as jy 'n video maak van die restureer werk wat jy gaan doen aan die saag. Groete David vanaf die Vaal Driehoek af.

Thank you for this informative video. I did my heater control valve and replaced the 20 year old factory installed thermo housing and replaced it with an aluminium housing today. The only difficult part was the big return hose at the bottom. Can you please make a video on how to replace the stàbiliser bar bushes. That is my next battle Thank you

Thank you sir, this helped a lot

Gentlemen? Well, that's me off then!

Fuite d'huile au carter ? Bagnole à la casse. Chaine de distribution ? Bagnole à la casse. Ampoule grillée ? Bagnole à la casse... 😄

Hi sir, I have a 1.3 ford ka, it did not have a heater valve fitted, I am fitting one now but I cannot find a diagram to show the pipe connection sequence to the thermostat, can you help maybe?

Good day boss what causes humming noise on a ford bantam 1.3l

Can we stand together and sue Ford for negligence in design?

Mine doesn't be warm it make noise

Thank you to teach us mine the engine is vibrating misfiring

Daai ram gaan n lekker tyd he!

So is incgo a good brand to buy spanners in

Don have a welder can you buy an extender anywhere

So the other day i was working on a suspension the bolts 22 mm where very tight so to crack them loose i locked the 22 mm spanner to a 24 mm spanner and did the two spanner trick then noticed a small dent deformation in the corner of the open end is thst normal for a quality tool if so are there less damaging methods to get more leverage on a combo spanner

Ek het laas een gemaak toe ek 14 jaar oud was, jou metode is natuurlik baie beter 👍🏼.

Thanks!

How did you remove the embossed drill identifiers from the shank of the high speed steel bit? These embossed, drill bit size identifiers would create and uneven and upset metal surface which would compromise the smoothness necessary on a burnishing tool. I know it could be done with abrasives in a lathe, but then the high-speed steel would have to be polished. I don't see this process portrayed in your video.

Morning , your video was excellent, thanks

At 0:32 what is that pipe with the white plastic and metal tip used for that goes into the top of the engine into that ring thing?

vice grip for clamps works much better. give i try.

Could you quickly explain how to remove the passenger side airbag panel please?

Keep the wrench in the undo position, so when you turn the tool to cut the wire, it tights further the loops. Also instead of the front hole, install a small rod, to constrain better the wire near the edge.

200n/m for the rear bearing???????????

Hello , ive replaced the timing chain but still has a noice , what else can i look at ?

Hi jaco i have a ford bantam crank but no start please help...

can't find the fuse....?

Ford bantum rocam how to put head sens

interrupteur de meule à disque

Vidoe bleeding clutch please