Відео

I appreciate the respect you have for your truck. Look at them wheels! (I'm jealous) P255/60 R60 I run "LT" all terrain at 40 psi each. Clean work my guy. Is the rear an 8.8 or 7.5? Glade you kept the fork in exhaust. A new front clip and lights. If it not off road ready or 4x4 I personally remove brush guard to free up wight and slim up the front. Love it tho.

Thank you!!!!

No worries... looks like your truck has the 300 6 cylinder.

Question Can that be the same as a 1993 Ford F-150 5.0 engine to Please let Me know.If so you solve My problem. Help

WoW and I been timing it at 0 or 10 degree not at that nock. That's why my truck is missing every time I start it. I hope this works I tried everything. I hope this is the same as a 5.0 engine 1993 ford f-150.

Hey, I just got a 92 f150 and drove it from Oregon to Arizona where it had been sitting undriven for 5 or 6 years. Random question, how did you get the seat to stay tilted forward? I don’t think mine does that and it was a pain to load. Maybe I just don’t know how to do it?

Ive had several 80s and 90s ford and chevy trucks all in various conditions and i have never once had and issue with ford handles. Every single ford ive ever owned had the original door handles aswell. Chevys however seem to break if you look at them wrong. Especially the tailgate handles on the 90s and 2000s Chevys never had an issue on a ford tailgate either and the beds of the fords are always beat to hell my daily obs f250 right now the bed almost touches the cab and its not even remotely square anymore and the tailgate is banana shaped and it works fine given you slam it hard enough only issue i have with it not closing is when i let Chevy guys close it and they're so used to being gentle on them because their trucks will break otherwise. Anyway everytime i let them do that the tailgate ends up falling off even drug it down the road for a good 1/8 mile buy the single cable holding it on put it back on and it still works just fine.

Im looking for one

Is it the same for 1986? Is there a similar “spout” connector?

thanks very helpful video

I just picked up a 93 F150 super cab with the inline 6 5 speed manual transmission 4×4 for 600 and it was running...for 90 miles before the clutch went out but the seller told me that it was going out and had the brand new clutch kit. Needs a bit of love but she's my new baby so I'm going to get her up and running again.

Thanks but i have 2 timing indentations on my 1983 f150 4.9l Two little triangular indentations on the cam on mine. I dont know which one to use!!! There is no little line on mine like yours. At all! TWO triangular indentations. And i cannot tel which one is the right one!!

I'm a Pete G. My Yawtay and i love white PAWGS, but they're afraid of my color,so i sprayed some Easy Off on my body,and washed it off at the car wash late at night when no one was up, and now i get all the white women PAWGS because i'm almost blinging silver like them wheels doh.

Did you ever install the spoiler you found at the junkyard

Redine it. Rev that to the moon homie

The roof looks clean asf without a headliner

Nobody gives a f*** what you look like

You're a f****** dumbass quit moving the camera around all over the place and show people the f*** you're talking about

Троит двигатель 4.9 Форд эконолайн как настроить зажигание вы не подскажете?

Que medida son los espaciadores

Is this the same for a 95 f150?

Orale vato

My 93 4.9 L6 is at 318,000 miles I know this truck will make it past 400,000

Usa.... mestres do BMX😊😊😊

Quero uma dessas relaçanda😮😮😊

buen video! me sirvió para darme una idea yo le pondré 1.5’ pulgadas. saludos desde Los mochis sinaloa

10 degrees BTDC can be stated as being Below or Before top dead center. I have O mark and below that is 10 and above that is 10. If i bring my timing to match the first one i get a low low RPM and shutters and quits. I cannot go to 0 at all as it dies as soon as i bring it there and no way can i go past the 0 on the balancer. 1996 4.9

@EseOGPanchito How long did you leave the oven cleaner on?? Which works best, the Goo Gone or the Oven Cleaner?

I used a white paint pen to highlight mark. A remote starter switch is a great tool for getting this lined up..

Got some big spacers on those tires, huh? If you shaved the front pointed spots they wint poke so much

ua-cam.com/users/shortsOxCMznfD5ZA?si=QCcKprJdZNPS9kxT

Como fue tu experiencia en todo este tiempo ?

Debes agregar bujes de centrado. Para tu Seguridad

Thanks so much! This was a lot of help!

Did you end up stacking the spacers or just 2 inch all around?

best ever!

93 f150 😊

F@&$ yeah dude! I wish my truck had that!!!

Mines got like four inches of play in gear, does it also fix that?

Whered you get your front bumper? Dod you make it?

Sounds great need to do this to my 96 obs. Do you have a link for the spike lug nuts? That looks awesome

Good info- thanks!!

Please stop fast forward your voice it's not helping

You video was helpful, cudnt decide wut tire I wanted to go with but this helped me make a decision

I know i am coming late to this, but i just got my thermostat replaced and now i am getting low temperature readings too. My engine runs fine and heater works good. Did you manage to solve your issue?

Very smart feller . Appreciate the video sir . I had mine about 120 degrees out. I was getting so much pre ignition knock I thought I had left something in the hole after changing my distributor out . Keep Making content .we're watching

Sounds good! I bet it responds better on the road.

Well sh!t. 😂 I just checked my timing cause my truck wanted to steal sometimes at a stop. Stupid me didn't see that tiny timing mark that looks like a Crack. I went off the cut out looking part on the balancer. Oops! I'm re timing it tomorrow 😂 thanks for the video

Thanks! Quick and easy 👍🏽🤙🏽

Se oye chingona yo en mi caso dejaría los catalizadores