Відео

I quite like this pedal its so bad its good i love the farty maestro fuzz tone like sound

Exactly what I needed to know on this date: Aug 4, 2024. So, thank you!

DID YOU USE THE -10 DB FILTRE OR NATURAL POSTITION IN THIS TEST ?

A little tip,as the waterslide paper is not cheap just as acetate sheets for making PCBs also is not cheap,print the image you want in low res on paper first then cut out a slightly larger piece of waterslide paper and tape it over the low res image on the paper sheet using masking tape low tack type should be best. Then print the full res image using the normal paper carrier sheet this will reduce massive waste of the waterslide paper allowing multiple prints from a single A4 sheet instead of one sheet per print.

I love mine! Any idea where I can find racks?

Nice one dude. Great version

"OH-HIGH"

i think the 5088 has a bunch more gain than a 2222.. mine measure in the 500-600 range and 2222 is something like 250 i think.. 5088 is in a lot of boost designs i have come across.. nice quick build!

Thanks for this

This is a great vid and I’m going to build one with an addition. I’m going to add power jack outs for each channel so the pedals that are in each loop can get power from this looper. I’m sure I’ll need to find a way to do that, but since I’ll use mine for OD/drive, the mA for all 4 would be under 500 mA I’m sure. Great video man.

Does the velcro on the pedalboard easily go off? I want to get one but after years of issues with standard velcro I want to use dual lock.

I just did this and now pads are launching sound when I tap a nearby pad or even when I just bump the controller by the accident. The intended pad has better sensitivity but I obviously can't have other pads making noise unintentionally. At least I can reinstall the plastic piece.

WTH ?! you spend all that time mixing and not let us hear the result ? why waste our time with that then ??????

Thanks Liam - that was really useful!

Not enough juice from a piezo.

Does it have any information printed on front? Is it black?

You think you have a real one. Who knows 🤷‍♂️

Great job!! Loved it!!

I’ve cramps in my fingers just from watching this video. Sucks to get old. BTW, great job!👏

We bought our daughter's this make and model in the 80's and had much fun! I dug it out and can not find the adapter Direct piece yu say you used something else and an adapter so it would work. What kind of adapter did you use with that adapter and where did you find it? Thanks...😀

Con Que Programa Lk Trabajas

OMG. U do not help at all!!!!

What’s the deadpool pedal?

I ALWAYS use a pre-amp if im using a Piezo

Amerikan sound is Fender-ish and Brittish is Marshall-ish

Thanks, helped in 2024 :D

these are the EXACT SAME as the German brand Palmer. Basically these are the Palmer pedalbay pedal boards but a bit cheaper than they, only thing I notice different is obviously the branding on the bag and the elastics are thinner than on the Palmer. Exact same bag and board...they must have a deal with Palmer to sell these under the HB brandname.

Hey mate, in your case you are right. You dont need 4 cable method. Only thing is, you mentioned it, it should go to the end of your chain on the floor, coz at the beginning you are really silencing your guitar noise and nothing else with pedals. The 4 cable method is for (a bit better) amps so you have on your amp: a normal in, an FX send, and an FX return. You can silence the noisy pedals, and amp noise, so go from guitar into silencer input, from its output you make your chain and go into the amp in... back out from FX send ( on Amp) to the silencer (into its return) and then go on from its normal out to amp FX return. I think it should be correct. No promise. But not all the amps have send and return. Mine doesn't. Cheers

This seem misguiding, because there is no way that this circuit can do latch or unlatch without relay and temporary switch, so this is not a fs6 clone, just a "simple" double footswitch with reversible polarity wich is about half of what the fs6 is about.

hello how can i contact with you???

Огромное тебе человеческое СПАСИБО!

Kinda hard to hear the pedal when the video has background music playing (approximately around 6:30).

Would you know if this would work on the hold function of the Boss sy-1 pedal ? I think the fs-6 is what they recommend. Thanks.

Ojay’s was a funk band from the 70’s. This is an Ojai (oh-hi)

What's the model of the pedal board? I know its harley benton spaceship but what size?

Is that a classical Guitar with different machine heads and metal strings?

Wasn’t very helpful, but at least it entertained me.

The level knob controls the amount of chorus effect you want to add to the dry signal. All the way to the left=dry signal only. Turn knob clockwise to blend in the amount of chorus you set with the rate and depth knobs.😀

IMHO it is easier to build if you put all the wires on the case mounted components first. Install them then for the wires you are soldering on the pcb not in all sorts of wonky places

If you open it would be super easy to tell its digital or not...EDIT: I just realized, with that amount of power needed, definitely digital. A regular MXR phaser needs less than 10ma.

Excelente trabajo, muy buen proyecto

The first ever UA-cam demo of this amps gain potential

All hail Monolord🤘

Nice video. I was wondering how you could do a footswitch like that for a 4 channels amp like the marshal mg15fx?

Thanks very much!

How do i add my own sampler sound to the pad.

I think there are different circumstances like you said. Mine works much better with your setup before all my effects pedals, after the tuner. I have a PRS MT15 with an extremely noisy lead channel and effects loop. Putting it in front calmed it down better than the 4CM in the effects loop. Thanks for the video!

What kind of paint did you use? And which kinds would stick well? I guess paint hard to touch could improve the reflectivity at the higher frequencies???

I found this video, as I am curious about the concept of a Phaser with Reverb after effects. It sounds cool! Thank you!

DPDT swich is ON/ON or ON/OFF ?