Відео

Está impresora es una pasada. Muy bien

Where can we get the slicer setting ? I'm struggling with....

Question what was the X Y Z in MM

I have a kingroon kp3s v1. Can I set up octoprint with this? It does not have a usb port, but there is a connector inside when the bottom plate is removed which has vcc tx rx gnd, can I use that as interface?

For folks working on this, I've made a little print to mark out the centre of the support pillars on the magnetic sheet. Then I used a 2mm drill to clear the holes for the Alan Key (those being 2.5mm). The screws have enough clearance apparently to not get much resistance from the glue. You can just screw them out with minimal damage. If placing the screws on the underside the next time is not possible, it would be nice to have some hole cut from the factory.

my fan is too strong and blows the filament off and cant adjust it

could you print one for me?

i need to buy a new Linear Rail Guide , where can i find? tks

Hey can you give me the model for the box?

I upload printer.cfg, but it has problem cannot parse z offsset..

Thanks!

I have a rainbow one it’s cool lol

I can't make the filament get out of the hotend, what could I do to solve it?

Where can I find the stl?

Can you please provide gcode file in description

For folks without paper, I've found a 5cent coin to work as well for spacing.

How long was the print

Do I need to tighten or not the bearing and brass screws?

It's perfect, the most annoying thing is calibrating this printer and this update improves the only negative point of this printer

Mc nuckels

Can you print one for me to please

Can you print one for me to please

Hi! Great video! I follow all but when i press autolevel,the hotend goesmake only a "home". Maybe do you know why? Thank you

Hello, does it apply to klp1(version 210)

After install camera for KLP1(version 210), how to setup the timelapse on KLP1 Thanks

The main question is what use is the autolevel?, if in the end the bed does not move and only the nozzle moves when it touches the bed or print parts and unscrews. It would then be like adding another thing to adjust instead of helping, it creates another problem because you always have to adjust the bed to the nozzle and then adjust the autolevel. I really don't see the point.

I bought one today but still delivering

Acho que a firmware original é muito ruinzinha e a mudança da placa com o chip novo prejudicou ainda mais. A minha veio com o chip mais novo. Consegui programar um firmware marlin sem ter que mudar a posição do LCD. Coloquei o bltouch Agora removi o cooler de material, porque não uso e prejudica o acesso à extrusora. É uma máquina boa, mas pecaram em alguns itens, como aquela fonte externa.

Can ypu guys make a video tutorial about and LED install on KLP1 230 printer please? I got one recently and I would like to make that upgrade

I can't find the superSlicer profile :(

Обдув кверх ногами поставил провода в верх должны быть.

It looks very blurry

Hello! Who made the file? How can I get/buy the file?

Bro , please make a video how to order that

Cool Modelling !! Also could you tell me the name of this song in the background?

Can I use any lazer head?

hi, im trying to print the main part of this helmet but i failed 20 times what is the config you used?

Fake

There’s a separate piece of cigarette. They accidentally knock the middle before doing the trick and as you can see the real cigarette doesn’t move

Soy el unico que penso que pondrían la musica del medio oeste de PVZ?

El desarmador de 2mm. A que se refiere al diametro en general del desarmador o a alguna medida que tiene la punta del desarmador.

It's magentic

i love how the middle piece of the cigarette suddenly gains a bunch of wrinkles when you move it

Link?

выложите образы дисеа рабочие. те что на оф сайте не вдиваются в флешку

It's looks good

Nice, stl?

STL ??????

Cut your damn nails It's horrible to have to see that. or at least clean them ...

Pls share STL