Відео

Thanks for the knowledge you share.

Whats the selary

Are rescue boats also fitted with motors(motor boats with fuel!?)

Need po ba patayin yung mgps or okay na po yung i zero yung ampere settings po?

Congrats Bro.

❤

Nice video, thanks for sharing.

Thank you, Sir, for providing the education. But I am a cadet and haven’t had the chance to learn about this yet. Can you please show me how to read the plywell to determine the top position on the cylinder that will be adjusted? And what are the steps, Sir? Should I adjust in order from 1, 2, 3, 4, and 5, or can it be done in any sequence? I would appreciate your guidance.

Sir wla bang fuel oil duplex filter ang GE na yan.

Thank u so much for giving this information. I didn't know the rescue boat davit. Just heard about it but confused about davit that what it is

How many blowers running need to maintenance engine room air flowing control. &how engine room air pressure &volume maintain &how pressure measurements at engine room. Can be fitted air flowing system at engine room.

You didn’t show the sign in process in the lounge. What documents do they ask for or what status do you need?

Mr please give some video, how to press test the hydrolic crane

Why are you not safety gloves for your Hands?

my friend, you are an idi.t

Terrible music

I was hoping for seeing an re-adjustment when it has shifted.

In my engine , the down line is mouting position mark line and the top line is Initial injection mark line .

Hi. Sorry to say but this video is absolutelly wrong. First of all you are not carrying out ANY timing. You just checked if pump is at the line in beggining of delivery. You shown you adjust 11,5 degree... but this is not true... Timing is adjusted according to upper line. And you are turning the engine in wrong direction and also showing wrong stroke, you checked all when piston was at BDC. All video is completely not good. Sorry. As a proove look at your video, you are showing each pump timing at the end. Fuel cams are in different position, but each one should be at the same if they are all 11,5 degree before TDC

Friends, what a kind of paste or grease did you use between flanges?

Thanks for your video

Have a good vacation my friend. Salute from Turkiye 🙋‍♂️

hello,sir,can you tell me how the two ball bearings are installed? face to face /back to back/series?

🙏 thx

Kuripearl ba gamit mu sir? Ilang liters nilagay mu sir ska fresh water?

Which is maker and model of bilge seperator?? Is it ush-20 ?

Goos day sir ask ko lang po anong problema kapag hindi ng oopen ang grabs bucket salamat

Your video is awful at all. You don't even realize what is showing on dialgauge and you don't quite know markings on flywheel. For 55Deg BBDC, u r showing 55D ABDC. And also the way u understand how dial gauge is used on tappet clearance measurement is wrong. Hope u study more

Hindi po malinaw voice over nyo sir para nyo po kinakain ang mga words. pero tnx for the content

Anong dahilan o problema sa low insulation pag inooff ang mga breaker ay tumataas lalo yung level. Pero pag ibalik mo ay bumababa.

Sir mali naman po ang timing nyo..ung taas na guhit po ang timing ng 5dc-17a. Saka standard shim height 0.5mm para makuha ang 11.5 deg. B.T.D.C

Show suction valve also before showing punture valve insertion into fuel pump..

Siya pa lang yung siopai king.

I'm not sure what I just watched.

Sir, thank you very much for the video! What does the top line mean? Where are the shims installed?

Merry Christmas, thank you for your service to global commers.

Minta tolong kasih penjelasan nya bas

ممكن رسم تخطيطي للكباش

ممكن رسم تخطيطي للدايرة الخاصة cerCet pdf

I believe you bro, if your staff is experienced, you can do it.

❤❤ Could u explain What time we can change Fo to Do and Do to Fo? Why should we change?? If u do not mind, Pleased answer me.❤❤😊😊

What the name of chemical sir ?

Super

Mag tagalog ka nalang bro

you shuold know what you measured is vv clearance.dial gauge showing distance not degree.your valve clearance also incorrect .actually is 0.35mm.manual is 0.3mm.😊hope you have more 3rd engineer experience. hard study and back again with correct video.

your vedio is not correct to check valve clearance .you confused valve timing and valve clearance.

Can i join with you

ooh...enjoyed your video...great learning😇

Sir please make a video on basis of davit lifeboat Motor wiring diagram

Sir can you provide me wiring diagram.