26
177 633

Honda XL500s 1979 Carburater floatlevel check and adjustment

5:46

Honda XL500 Chaintensioner adjusting is so easy

0:16

Honda XL500s 1979 Startup day1 check

3:17

CJ's Garage 60 seconds review makita 18v impactdriver tool 2020

1:01

Final Phase 9 Honda XR600 Oilpump Priming Startup Breakin Procedure

10:44

Phase 8 Short Cover Story

2:03

Honda XL500s Clutch plates and springs EBC 21jan2021

Changing the clutch plates on my XL500s. After i got the carburator working i noticed the plates were slipping when applying throttle.
Also changed the clutchsprings with the EBC clutchsprings. After the change the bike is responding very good, clutch feeling is perfect.
Tip: soak the new plates in motorcycle engine oil the night before.
Keep It Real van Audionautix is gelicentieerd onder een Creative Commons Attribution 4.0-licentie. creativecommons.org/licenses/by/4.0/
Artiest: audionautix.com/

Відео

Honda XL500s 1979 Carburater floatlevel check and adjustment

5:46

Honda XL500s 1979 Carburater floatlevel check and adjustment

Переглядів 3 тис.4 роки тому

Honda XL500s 1979 The bike wouldnt't run, even with compression and spark. So there had to be something with timing or fuel. Checked the carb and cleaned it, found out that the float was not according to specs. Adjusted the float as described in the manual, now the bike runs great! Clutchplates are slipping, so the next video will be about changing the clutchplates and springs. Carb: PD08 Float...

Honda XL500 Chaintensioner adjusting is so easy

0:16

Honda XL500 Chaintensioner adjusting is so easy

Переглядів 4,3 тис.4 роки тому

Honda thumpers can get noisy in the head when the camchain doesn't have the right tension anymore. The XL500 has an easy way to put the tension on the chain again! Loosen the nuts as shown in the video, the noise dissapeared from the head. You can do this a few times until the camchain is really worn. If the sound doesn't dissapear it's TIME for a new chain ;)

3:17

Honda XL500s 1979 Startup day1 check

Переглядів 3,6 тис.4 роки тому

Bought this great oldtimer last weekend. One of the first members of the XL/XR family. Wet sump, single cylinder engine. Previous owner said the engine didn't start easily, something with the fuel. So I did a first checkup of the bike before removing the carburetor. - Compressioncheck - Sparkcheck - Bikecheck Next video: - Inspection of the carburetor - Cleaning of the carburetor - Assembly of ...

CJ's Garage 60 seconds review makita 18v impactdriver tool 2020

1:01

CJ's Garage 60 seconds review makita 18v impactdriver tool 2020

Переглядів 1524 роки тому

Fast review of my new 18V Makita 3/8 impactdriver tool. Three different settings, i love the autostop modus! Small and powerfull, and an easy combination with the other tools with swapping the same 18V battery. Music by: www.bensound.com/

Final Phase 9 Honda XR600 Oilpump Priming Startup Breakin Procedure

10:44

Final Phase 9 Honda XR600 Oilpump Priming Startup Breakin Procedure

Переглядів 20 тис.5 років тому

After installing the engine in the frame, i primed the oilpump to prevent an airlock. I tried to do this in the best possible way, in different steps to insure i have oilflow in the system. When the bike started up, i followed the "hard break-in" procedure to get the best possible seal between the pistonrings and the cylinderwall. First 30km (20mls) 1500 to 3000rpm (using gaspressure!!!) Oilcha...

2:03

Phase 8 Short Cover Story

Переглядів 2,7 тис.5 років тому

Preparing the clutch and statorcover after spraying it with the Motip 51230 colour.

9:15

Phase7 Cylinderhead Honda XR600R

Переглядів 60 тис.5 років тому

Checking and installing cylinderhead on a Honda XR600 1987 PE-04. - Plastigauge - Valveguide measurements - Lapping the valves (not included in video, see in-video link)

1:35

Long story short

Переглядів 1465 років тому

Circuit Assen, welcomed by the Greenpower CIP Team MOTO3 from Darryn Binder and Tom Booth-Amos. Short footage of the circuit. Great weekend! Heard the moto2 Triumph for the first time, they made great engines!

2:11

TT Assen campground raw material 2019

Переглядів 5335 років тому

Campground around Assen ciruit, love this place. See you next year!

0:11

Comming up, Phase 7 Cylinderhead

Переглядів 3225 років тому

Installation: - Cylinderhead assembly - Camshaft - Camchain - Valvecover -

Phase 6 Cylinder honing and installation

9:40

Phase 6 Cylinder honing and installation

Переглядів 6 тис.5 років тому

Honing the cylinder of a Honda XR600 1987. Measurements, and then honing the cylinder to roughen up the cylinderwall. Installation of the piston and cylinder. Thanks to: XR land: ua-cam.com/video/LpXz-tvpIPE/v-deo.html ua-cam.com/users/XRLandvideos TKRJ Website: www.tkrj.co.jp/ TKRJ catalogue: www.tkrj.co.jp/pdf/catalog.pdf Download the measuring report by clicking on this link: www.docdroid.ne...

Phase 5 Installing kickstarter, clutchhousing, idlergear, rotor.

4:04

Phase 5 Installing kickstarter, clutchhousing, idlergear, rotor.

Переглядів 6 тис.5 років тому

Filling the inside of the clutchcover with the kickstarter, idlergear, clutchhousing. On the other side of the engine i also installed the roter and applied the right torque. Next video will be honing of the cylinderwall and installing the piston and cylinder! Music: www.bensound.com

Phase 4 oilpump measurement assembly and test16may2019

8:45

Phase 4 oilpump measurement assembly and test16may2019

Переглядів 3,3 тис.5 років тому

Measuring, installing and primary testing the oilpump. The final testing will be done when the engine is in the frame and the oil lines are attached. The oilflow will be checked again, and before the initial start the oilpump will be primed. Measurements in pdf file: docdro.id/5QkfqiZ Full engine measurement file will be out as soon as the engine is ready. Music by: Music: www.bensound.com