Відео

A shorty rear end should do even with a 12” upset

Some interesting info and humor, I had to subscribe. Just hope ur other videos don't suck! Good job ill watch more.

What would a job like that cost on a square body

So apparently you can actually use PN 26015779. I believe it’s the steering shaft in the c3500. I’ve read that you don’t need to make any modifications either and would eliminate the rag joint. I’m about to try this myself and see if it works

These saws are amazing! Best tool I have. ❤

Let's Geaux!!! Get the content flowing!!!

I want to get my 03 f150 slammed on air where should I be looking for parts and knowledge

How can you end it without a full body shot with the wheels! 😂

Where can I get the air bags cups ??

Step 2 Hawk tuah spit on that thang got it lmao 😂

best video ive seen , super good...

I would love to know the next car meet. I would love to go so i can get some ideas for my truck

Great tip, thanks 👍

Do you have the link for the control arms & are they on drop springs ?

👍🏽oh yeah Stretch Cruiser Life, Love mine

Do you think it’s possible to do this on a 4 wheel drive if it’s on a leveling kit or stock height?

22x10.5” will tuck. Check out my videos of my obs.

Years ago I made one work by just shorting the axle tubes . Unless you absolutely love the wheels don’t advise . Shit ton of work and a few trashed cut parts that wouldn’t fit . But it still rolls around NJ to this day somewhere up there

Great video! Very helpful, thank you.

The 84-94 XJ/Cherokee shaft(95+ XJ shafts are clocked 90 degrees different) works just fine on ALL GM trucks that have the steering column extending through the firewall with both joints being under the hood. For the US OBS trucks in 95 GM changed steering columns when they added in the air bag, it is a much shorter column using a 2 piece steering shaft with the upper joint now being under the dash inside the cab, so installing the XJ shaft is much more work in them as you have to cut the lower joint off, and graft it onto the stock 95+ shaft. Installing the XJ shaft in place of the lower shaft on a 95+ WILL result in a loss of steering going down the road as it adds in a 3rd joint in the middle of the shaft that will be un-supported.

Is this the same part and procedure for the K1500 4x4?

I'm wanting to run the torque thrust 2s 22x9 22x11 265 30 up front 295 30 in the back 4 7 drop will it clear or need to be trimmed an rolled a lot? And am I going to run into problems wanting to drive it a lot? It's also a step side.

Will this bag set up be the same if i want to bag my extended cab obs?

Great vid. I’m doing the hoppos f/b/ss setup in my 1963 Impala. I have the bags in. 1/2” line is about to be run to the trunk. Will be running 2 -5gal tanks. And either 2 or 3 pumps. I have 2 444c viair pumps. Was thinking of getting 1 more pump. So I have air for days to play. This vid was super informative and I subscribed. Thanks bro.

i got the same wheels but in 10.5 inch i believe but i only paid 1685

Wow that paint really brought the old girl back to life and the exhaust sounds sooooo goood

I just bought the one from Cunningham machine and its exactly the same as that with no modifications. Just bolts right in and i think it was only like $80. Come to find out most of my slack on my 95 Silverado was the pitman arm needing replaced after i replaced both it helps tremendously.

What a hell have happened in this tank 😂. Looks like some took s turd in there. Changed mine 2011. Never look bad like that.

G'day ... New Sub here!! Love the work!! from Brooksys channel!!

Tons of clean rides.

Did you go with a narrower track width on the front arms? If so, how much?

Hey i got the exact dame single cab bubble eye ,whats a good complete kit i can buy and where because ive seen a few and dont know which one to get,a few of them look different

Love this But it still seems kinda dark to me

In my opinion OBS is 47-54 Chevy.

No comment

I have a 92 dually obs running the 3 link kit with upper bridge and triple bellow semi truck bags, how do I find my half travel. Do it put the wheels I ll be running and let the frame sit on read end then weld everything in ?

What is the size of the tire not the rim

LOVE this! Was a great night!

That’s badass and he is awesome at what he does. Thanks for all the great pics Tony.

He is willy mess up that 90 truck i would never do that My name Bill Thompson I own a 1992 Chevy Silverado extended cab pick up truck I about to restore it myself i to me the 90's Chevy trucks is one the best looking trucks that Chevy ever made i we never get rid of my at all 😊

can you do a diagram on how to wire the toggle switch on the airlift v2 system? I'm wanting a way to put a toggle on my system that way I can crank the car before I have to turn air compressor on. this way won't drain battery to fast. I already have the system on the car, just wanting a way to wire toggle switch on it. Thanks in advance.. enjoyed your video.

Adam is a good Dude, and a good paint instructor. Adams Lime Line Brand and Time Warp Custom paint is Top Notch paints Pigments Candies and equipment.

Where's the truck that's in the clickbait picture ?

If you still haven’t tried the Upol clear give it a shot… for the money it’s hard to beat, sprays great and flows out really well.

Nice but it’s like putting perfume on a pig.

Coolest thing about the teuck scene is that they show their unfinished projects and thats cool. As a lowrider its rare anyone building a lowrider allows their ride to be seen untill it's finished. Lobe the mods on that teuck

Work in progress. ❤❤

Been restoring my 96 K1500 she’s not far off from finished. Love seeing these unique builds!

295/30 or 295/25 which will look better?

Have a 91 Mazda B22 chopped and slammed convertable with 16" windshield almost finished.