Відео

You do know your ingine fan is blowing in the direction of your cooling fan best pull hot air out just saying don't trap the heat

Real Redneck install on the fan. I put my inside and It can't be seen. I did add a second Battery to help out The charging system.. plus it adds extra weight To the machine. I love my machine So far... 25 hrs with No issues... I did cut the flat edge Off the front of my Bucket ant welded On a cutting edge And what a difference that made in digging...

What type of oil does it take?

You take ceramic wool. It good

Tu n' as pas niaiser avec ça toi zip cutter dans le body😅

Love the heat shield idea! Ive thought about taking the pull start housing off to expose the motor cooling fins, and running some sort of duct to the side of the excavator where cool air can come in. Seems like it just brings in hot air the way it is. Raising the seat up a couple of inches to let heat escape might be a modification I do in the near future. Also, My hudraulics get way too hot, so i will most likely be installing a oil cooler, and a flexible 200 watt solar panel to mount to the top of the canopy for another fan or to keep the battery charged. My bigest complaint about the machine is how slow the tracks are. Especialy if the drive motors get hot. NOTE: These machines have a 9 amp charging stator, so do not exceed this or you'll start to drain the battery. Is why ill probably install a solar panel.

You should tack weld nuts on back..to remove fan for service.

Does the engine make enough amps to keep the battery charged or do you plug a charger in when not using?

Were did u buy them

this mod could have easily been kept internal for a cleaner look and not getting hit during operation though...I've got a similar internal mod in the works on my H12

I've seen a few people Mount them without cutting the metal out. They mount it on the inside, and you can't even tell it's there now you have nothing to protect your fans.

Is it just me or does anyone else think that looks like fuk?

I am going with 2 7 in fans

In just got one of these, hydraulic oil level seems to be low on that little glass bubble. It is below the red dot and the tank is already full. Do you know if this is normal ???

Does the electrical system have an alternator or anything to maintain battery voltage?

What kind of hydraulic fluid do you use?

Great video! Looking to put fans on my unit myself I just reached 5 hrs on it and am looking to do an oil change. Do you happen to know if these engines have an oil filter? And what weight oil did you put in?

good job, i would close the holes upper the fan, to can not circulate (a circl like 2-3 inch airflow next to the fan)

I just got my fans in and will be installing 2 with the push pull technique. Each fan will be mounted inside the housing facing out. There is a spare wires that is not being used inside under the throttle and key switch area. It is there for extra lights. One wire is hot all the time and is hooked to the battery disconnect and another that is switched by the light switch. They also have a ground in the bundle. Saves you from having to run wires. There is room inside the engine compartment to mount the fans so you don't have to worry about damaging the fan while you are operating the excavator in heavily cluttered areas.

Can you please post a link to the fan you used?

Update, ive put 6 hours of hard work on this machine since installing fan. It has stayed cool and done a good job. I need to do another oil change and grease everything. Thanks for watching 👀

I am probably going to do this but add an in line switch so it's not running all the time.

Should add prolube next change proof is in the pudding

Is the fan pulling hot air out or pushing air into the engine compartment

Not able to have the extra hydraulic would kill that machine for me. Looks like you may have handle. Just no hoses

I have a HT-10BZ on the way. It comes with a hydraulic oil cooler. I also am planning on adding a fan on the left side, and I am going to try for an inside fan. Thanks for the video - it helps to see how other address the problem. I am wondering if that aluminum housing you build around the exhaust will block airflow and make it too hot. What if you cut the left side off and let the fan blow are over and out the back. Right now you have no airflow over the exhaust. Might that cause problems?

Don't think it motor oil, think it's like a seed oil. This way it's not classed as hazmat.

Il a pas moyen de linstaller parr en dedans du paneau sans tout couper ya deja des troues pour qui pouce sont air ?

Any concern about the fan using too much power and over working the charging system? Mine came with a hydraulic oil cooler with a fan on a switch. I’m wondering if adding another fan for the engine will cause electrical issues

Im a big fan of the Chinese mini excavator. You are a risk taker. It looked like you used your wife’s good scissors.

Why not pull the air out. There enough space to pull air around the motor. I would check the swing arm gear and make sure it is tight

Just picked up a mini excavator and i installed a 12" fan blowing the hot air out. I primarily did this because i dont want dirt and dust to get pulled into the engine bay. It works surprisingly well in cooling the excavator. I also used heat shield under the seat to keep my butt cooler while using it.

Thanks for the video Luke. I have the same machine (under a different name) and am finding it runs very hot. I am looking to do a fan like this or maybe a hydraulic cooler with a fan to do double duty.

They are nice machines for about half the cost. I purchased one about a month ago from Denny. I had mine shipped down to TX. It works perfect the work I do.

I just bought one of these mini excavators and will be doing this before I even start using it. Thanks! And looking forward to future videos on this machine!

your going to need the fan!!! I boiled my fuel and had to replace the carb!

Nice job Luke. I'm getting ready to buy a couple of fans for my Miva. It has pilot controls which puts all the hyd. lines right in the way for mounting the fans on the side like you did, I just might have to put it on the outside like you did. I'm thinking about a 9-inch fan on the side and out the back mounting a 12-inch fan. I thought about bolting it to the grill, but I don't know how I'll end up attaching it because of the curvature of the grill.

The nxt day i planted a dozen 2 gal trees. I dug nice, big and deep holes with the Mini then tilled in 60lbs of compost in each hole. It ran great the seat did not heat up like it used too and the gas tank was nice and cool after running machine. Hydraulic pump was hot. Not sure what optimum running temp for the hydraulics are.