Відео

Will use this when I get a little canoe ( I prefer them over kayaks), and for places to tie down those travel cargo bags ( i have a hardtop). and last, I'll definitely figure out something for a bike carrier, might have to get a separate carrier and not use the truck bed extender

mine lasted about a year and a half in the florida sun before it started to rip. taped up a few parts and lasted another 6 months. just bought a replacement cover

thanx

You should only heat those bores where the wall is the thinnest.

NEVER use ratchet straps for securing kayaks, use cam straps

Plastic tubing or steel ?

Update please.

I got a 1020massey ferguson diesel tractor

Do you have a link to the bracket?

How durable would you say the cover is? Does it leak?

Dude, you're pretty ingenious.

Use pool noodles and duct tape on all the wear points and it should last alot longer.

I’m getting one to do some painting, I saw a kid paint a car in this and it turned out great , I’m just painting a few motorcycles so I think this will work just fine, thanks for the video

PTO over-running clutch should always be mounted on implement not tractor. As per Weasler web site, shaft is still dangerous if not covered via flywheel effect. Good luck 😊

It looks like a money pit to me.

From what I've gathered, though it does make it look better, keeping them tight puts pressure on the upper bends, and that's where they first wear holes. It's also recommended to use the noodle type pipe insulation on the upper bends/pressure points, and that they are covered with a new cheap tarp every year or so because the UV rays will cause the material to fail. But in the end, three years is longer than many of them last, however, some are getting ten years out of the cloth using those fairly simple tips. Thanks for the video.

Put pvc pipe in bottom of door and roll it up with door

The comments from you and others regarding snow removal tells me this does not shed snow properly. So a guy could not fill it items. He would need to leave an open path down the center so he could get inside and coax the snow off. Might be able to rig something long enough to pull the snow from outside but have to be careful not to puncture the fabric.

You can"t buy salvage parts at a reasonable price anymore. I bought a '51 8N for $800 in Feb. of '22 and had to replace entire valve train, starter, ring gear, clutch package,coil, points,condenser,radiator and water pump, not to mention a new battery and cables before I could tell what condition the engine was in. I got the tractor running a couple weeks ago and the engine starts right up and runs smooth BUT, it smokes and I'm sure it is going to require complete engine rebuild plus oilpump refurbish. After that, it needs new tires all around. I have around $1500 total in this thing now but I am keeping it for a working tractor.

Excellent video on the repair

Stick of pipe in the front door makes it easier to wall up and on mine first thing I did was cut off the velcros I made my own custom holders to keep the door up again put a pipe like electrical conduit makes rolling up 100 times easier

Awesome video!

This is a great solution for a JK. Any solutions for a JL? The light bar mounts don’t fit the same on the JL.

Thanks for sharing this. I was worried about longevity. They cost $250 now so that is a bit of cash to have rip up and be wasted in just one season. If mine will last at least three seasons in WI, I'll be happy.

does it smoke when u try starting it?

I would like to have some photos of direction I took mine down and moved it but can’t find directions

... this is actually a well made and informative little video on vintage tractor maintenance; deserves thousands of views, but - there aren't that many of us left, I suppose, who still screw on these pieces of archeology... Thank you Kind regards Kim

Dude, easiest sleeve install I’ve seen! You planned your work and worked your plan! 👍🏼 Thanks for great video!

That diagram on the card board is hard to see I wish you would've let us watch how you tighten everything down in sequence..

Hey Bud, did you need a hitch extension to clear your spare tire?

crack kills

On the sparkplug side

Hey I'm doing a head on a to- 30 I'm not sure it the head is different but I have tried many times to recreate what u did here with the 3/8 I can't get anything on the nuts to torque them any help would be appreciated thanks

back in the late 50-s we had a Layman boat, a good little wood boat

I live in the Foothills of the Catalina Mountains just North of Tucson and 3 years ago my "next door" neighbor, which actually about 2 and half miles away, bought one of these and put a simple 2x4 and plywood floor in it and lived in for over a year while they built their tiny cabin, worked fine for them. They turned it into a home bar/entertaining area after they moved into the cabin. It's been 3 year now and it's still doing fine.

How long of a roll pin? I bought one and had to buy roll pin separately and mines to long

Yep i feal ya i have 2,300 bucks into a to 20 that has just enough compression to run

I remember my dad, had a friend that had a boat, like that. And we went fishing all the time, in the summer. I loved that boat. I begged my dad to get a boat similar to the one you have. My dad was pretty tight with money, in those days, so no boat. I hope that it finds a good home. It has good bones, and a lot of potential, and in the end a person, would have a very desirable boat. I don't blame you for not taking on the project. And yes it would take a couple of years to restore it. But it sure would be fun. And imagine all the new skills that a person would learn. I have resurrected a couple of cars, and I sure learned a lot, and I still have them. And what a joy they are too me. That boat is a diamond in the rough. Good luck with what ever you decide to do with it.

I am having the same issue. I am getting low (about 30) compression in two cylinders. Did you figured out the reasons?

I have a to20 that runs good (finally). My worry is about the block cracking😅. Has this been a problem for you?

How is the tractor doing now?

Are you still planning on posting? I really find your video's helpful!

Ha ha, all that weight inside and I still blew off. My lazy but parked two tractors inside as soon as it went up. Then I rachet strapped the structure down to the tractors on either end.

Getting ready to do my own on a TO30. Thank you for the videos!

I have a 2018 wrangler JL 4 door soft top. Can you tell me the which light rack you purchased? Not sure on which one to go with.

I ended up taking my block to a machine shop where they hot tanked it and installed the sleeves. Freezing the sleeves did not work in my case and I broke two sleeves in the process. The sleeves are very brittle. I didn’t have a torch either. I would recommend a block of wood on top of that driver.

Excellent solution. Thanks for posting

Can you help with what you exactly used on back hitch?

Michigan winters says it all. I'll pick mine up this Friday.

I found out when i installed mine one was so tight, the last one, the others were snug and right, broke the tight one and found out that the liner was larger in diameter than the others. I was shipped a bad liner or one that was not machined exact. I recommend that you measure both the inside of the cylinder after slight honing and also the thickness of the liner and the actual round diameter.