Відео

Hi, thank you for the video. Have you noticed any issues when trying to use PC3 as GPIO? For me if I use PC3/PIN_A13,A13 (all refers to the same GPIO Pin) in digital write or read or analog read function, the result I get is to and from PA1. But if I use the pin number 20 for digital read and write then it works fine and sends or receives signals to PC3. But analog read always reads 0 if pin umber 20 is used. I am working with Arduino.

How to add NotePad++ Editor to Moun River with intelisence.

How to Change Tab Size From Default 4 to 8, I change it from Windows-> Preferences->General ->Editors->Text Editor and set Display Tab width = 8 but it does not Work. IDE is Moun River

Starting the debugger I get : Missing mandatory configuration. Fill-in the 'Config options:' field in the Debugger tab.

will it support Ch32V003 ?

How was noise immunization & performance in average

10,408 bytes to let CH32v003 blink with Arduino 😂 It seem to be 2x better now for only 5kb. Meanwhile people are bashing me for using 308 bytes to blink a PIC16 🤷‍♂️🫠

Plz full code video tutorial

Any chance you can show how this works for the datalogger video from #24 ?

Hi, How to Generate 1ms tick uding sys timer or Timer using Interrupt. Is there any Arduino library is there for precise time interval generation ?

No Arduino library for Timer, External Interrupt

How to use ws2811 led pixel with ch32x

Looking For Periodic Timer (Interrupt base) Arduino Library for CH32V003. All peripheral Example for CH32V003 are needed for Arduino. Or how to Implement EVT Board Code in Arduino?

@rvmaking would it be possible to pair a two of CH9160? Like one CH9160 used as a USB dongle, and other one paired up with CH32V307? Could it be connected to USB port of MCU, to then create a wireless connection with PC?

Because PIOC is located on the SWD pins, shouldn't be a good idea to put a small delay before the pins initialization just to ensure not to brick the MCU??

Thank you very much for doing our request.

❤😊

Do you have a link to buy the 8k usbhid chip?

Can you flash the ch9160 to be gamepad?

Great video, sir. Do you have a code repo and a pcb schematic/layout available?

Hello. After flashing CH32F207VC6 through openocd from MounRiver Studio under Linux i try to do Query chip info in WCH-Link Utility under Windows, and result is failed. But before flashing through openocd, WCH-Link Utility works fine. What happened? Thanks.

Can you provide link for the sample project being used here?

Appreciate if you can post a video on how to setup PIOC module. Thank you.

Very useful tutorial...just got me a CH32V307 board, will be trying some code soon.

thank you for this video because its really rear to see this support channel to add a new video about its own microcontroller. i have uploaded much more videos even tough i have less knowledge about this controller.

You say Arduino IDE but show what looks like VScode IDE. After adding the supplied URL to 'Additional Bd Manage URLs -- Then WCH to Board Manager brings up nothing. Poor poor poor ! I won't be using ANY of this.

Hi I would like to use CH32V003F4P6 board to connect with LCD 16x2 display to show text messages, can I use Arduino IDE to implement it?

flashing CH32V002 via arduino is not possible in Linux, USB not found error, WHC-LinkE appears as ttyACM0 flashing CH32V002 via arduino is only possible in w$, WCH-LinkE appears as COM(x)

Risc-V MCU is great.

good job.

Nice

Hello, is there any future plans on adding oled support or maybe Ethernet support like the winznet modules?

How to achieve 6mbps Max baudrate?

at 0:29: WCH-LinkE photo is wrong, it is WCH-Link (without "E") , it cannot program CH32V00..

Wonderful, thanks!

Just using bitbang and I call it end of day ! 3 bytes per pixel less code size simple to use.

Are all boards in the CH32V307 supported in the Arduino IDE? I only see a selection for CH32V307VCT6.

I haven't gone through all your videos yet, since I just subscribed. Did get the CH32V003F4P6-EVT working - because of your help. I'm wondering if it is possible to do PWM on some of these pins, like we do in the Arduino and other boards. I don't seem to see it called out as a function on the CH32 boards.

I have a stupid curiosity. I just received a CH32V003F4P6-EVT. When I run the GPIO toggle, nothing happened. But if I hooked up an external LED to PC_3, it did blink as programmed. I noticed in your program, that the LEDs on the board blinked. How did that happen?

First of all, thank you for your effort. Any suggestions about a problem: PD6 (RX pin) of the CH32V003F4P6 does not receive data over UART communication. PD5 (TX pin) works fine, sending data is not an issue. Tested with WCH LinkE + WCH-LinkE-R0-1v3 board and with ESP32 C3 too, CH32 was able to send but unsuccessful in receiving data. edit: Arduino Ide 2.3.2

Great opportunity to make Qi-capable device with lower BOM. Where can I buy some of this MCUs and possibly a dev board? Nothing is available from Ali shop and 3rd party sellers.

Here I noticed that this simple led blinking program using nearly 65% of program memory space and more than 10% of RAM.. what's the reason? Is it bcos of Arduino?

Hi, can i use ch32x035 USB pd to make a pd charger that can supply 20v or can it only act as client side

Hello, can you help me with one problem? I want to make an automatic window blind with servo and photoresistor, but i couldn’t figure it out, thanks CH32V003J4M6 Using only chip, without board

I use minichlink for this. The "-u" option will "unbrick" a chip. It needs to control power and be connected to pd1. I have never had it not work and I have tried to. I disabled PD7/nRST and PD1/SWDIO set them to GPIO immediately on startup. It still reaet it.

Im glad i found this channel. It helped alot in terms of understanding design. Thanks for your demo.

Nice work, nice project, thanks!

Fun project!

please guide for check spi communication in ch32v003???

hey, how do you make a analogRead? with analogRead(PA2) or other Analogpins i got nothing in return? digitalread is working? any ideas? thx