- 10
- 17 573
Vertamps
Приєднався 23 кві 2012
Fluke 343a Mod bd HV Capacitor Install
Mod boards to replace Sprague HV caps in an Fluke 343A DC voltage calibrator. Video thrown together for EEVBlog forum hang arounds.
Переглядів: 128
Відео
New 3456A + Show and Tell rack of gear
Переглядів 892 місяці тому
Showing of my new 3456A, out of the box tracks my other 3456A!
Beckman Helipot 20k Test and half Tear down
Переглядів 1002 місяці тому
Variable 5 watt multi turn precision wire wound potentiometer
KorgPoly61 Mod
Переглядів 2238 років тому
Master restored, complete cap job including correct bi-polar caps. All potentiometers disassembled, cleaned and lubricated tracks with special Nye lubricants. Professionally designed circuit mod for full control over the analog filters. Resurfaced key contacts and new high power lithium batter located separate on custom circuit board. Main synth dry audio recorded by a Tascam PortaOne studio ca...
Moog Satellite
Переглядів 4,9 тис.8 років тому
Fully refurbished, tuned, new filter capacitors and rebuilt slide potentiometers.
Crumar DP-30
Переглядів 6 тис.8 років тому
Restored Crumar DP-30. Velocity sensitive fully polyphonic analog synthesizer. A very rare synth that weighs in at 71lbs. (There is some camera mic distortion).
Prophet 600
Переглядів 76610 років тому
Fully functioning and electronically refurbished Sequential Circuits Prophet 600!
4X4 FUZZ pedal
Переглядів 30012 років тому
The 4X4 FUZZ showing off its wide sound pallet from clear and smooth to mushy vintage droning. Setup: 80's Peavey Predator - 4X4 FUZZ- clean 6 watt tube amp.
9:09 wp 👏👏👏
I had one of these back in the 1970's and I let go when I went to college. Aargh.
We love ours ☀️
Whoever disliked this is a d i c k bag. Very Great Video.
Moog's answer to the ARP Soloist (minus the aftertouch expression and more varied and useful tones in the Soloist)
the contour slider what is for? thank you
How much is a restore of one of these generally?
There isn't really an answer to this question - it very much depends on exactly what needs doing - and whether you have the skills to do it, or you need to pay someone else to do it. Replacement parts for vintage moogs are increasingly expensive to find. I'm just finishing off a Moog MG-1. The parts alone (new caps + new faders + foam + a couple of IC's) came to about $300. Add another $50-$70 for other cleaning products, e.g. deoxit/isopropyl etc. If you're paying someone to do it, this refurb took me about 8 days of full labour (YMMV - this one was in particularly terrible shape, with a lot of problems). If you're doing it yourself, you're going to need soldering iron, multimeter, and an oscilloscope at a minimum (as well as knowledge of how to diagnose electrical faults). So a repair cost could be super cheap, or it could be painfully expensive. There isn't a general answer, it very much depends on the synth in question, whether its fully working to begin with, and if not, which parts are not working!
@@robthebloke thankyou!
Have you ever run your finger across the glass display? It will cut you. That's one of my memories of this synth, plus, it had some great, multi-timbral sounds.
I own one!! Will never sell it. I replaced the battery just last year! Thanks to Midi-OX I was able to save all my custom sounds and load them back in the unit...
Me the same! :)
Who did the work? I would like restore mine.
I love my TQ5. Look at how amazing it looks in your video too - wonderful 80's design with the offset slashed square, the little black switches and that Guggenheim volume control. It's like an amazing sonic cake!
Hello!! I got one like this, but not sure how to replace battery, mine is not working well, please advise if you have a chance, Thanks!!!! OJ
I can help. On the bottom and the back of the unit or Phillips screws that you removed and the bottom comes off. Once you do that the battery can be replaced one caveat though, it's soldered to the board. What I did was used a CR2032 battery holder from an old motherboard. Hot glued it to an empty space and soldered the terminals to the board. Make sure you wire it using the right polarity. Work like a charm. I lost all my Custom Sounds, but luckily I found them on an old floppy I used the program called midi Ox to reload them.
Cool sounds. Just got a TQ5, do you know if there is anyway to loop the sequencer? Read the manual back to back, doesn't seem to be, but seems odd no to be able to loop!
No loop on the sequencer. That's just the way it was back then.
Hello, I want to refurbish also my Satellite. Where dir you get the fader potentiometer from? Or did you clean them and how. Thanks or an advice - Hagen from Germany
Casio CTK1000 :-D Cool.. I own one, and TQ5 too..
More video/ sound clips in different settings and also new amplifiers!
I hand built and designed it from the ground up. They can be purchased from Motor City Guitar in Waterford Michigan or directly from me (Vertical Amplifiers). It also works great for heavy metal rhythm tracks with different amplifiers. Email for inquire: vertamps@gmail.com -Will
nice distorter! Where did you get it?