Looked so easy in your video. My soldering iron didn't cut it just melted and I ended up ruining the board. Think I should have used a dremel and cutting disc.
Anyone that don’t wanna waste time with rebuilding the lights. Go to your GM dealership and tell them you want the revised part number tail light. The tail light is $205 through factory GM. Make sure to tell them you want the revised number. There was a recall on these for the 2015-2016 with the vehicle under 75,000 miles and they changed the light number
How do you know where to open the light to commence the repair? I am having a similar issue with Drivers Tail light working intermittently. Any advice would be appreciated. Your work is by far the best I have seen here on you tube.
Is amazing we as buyer have to do this crap because the LED strips GMC or Chevy use are very low quality. For an over 60k vehicle? Hahaha there is no shame.
Video is awesome and very thorough. How ever I didn’t see I this video until too late. First passenger attempt worked but middle 6 +/- bulbs are still out. Anyone know how to repair this?
@@mitchvillemaire8051 I finally fixed mine. After reading through hundreds of comments I finally figured out I had soldered the big gap section together. This causes the middle section of the taillight to go out. Only solder the hairline crack. If you did this go back in and cut the solder back out. This comment by Tom Maddox help the most Dude! You just saved me $800! Thank you! Great video. Explained well. The only thing that threw me was that the plastic was attached to the metal on the circuit board at the point of the hole you used to anchor the wire, so when I pried up my cut out, it was pulling on the metal. What threw me was a small metal "Bridge" appeared to connect both large pieces of metal. It looked like one end had cracked off and I figured I had broken the connection when I pried it up so I soldered that as well as the main break you show here. When I tested the light, the middle LED's did not light up. So I de-soldered the small "Bridge" and bent it out of the way so as not to make contact and that did it. I am still trying to figure out why that piece was there.
@Rodney Austin Thank you! For some reason when I applied 12v to that section I heard a small pop then it worked.. so it must of had a short some where. Since I only fixed the crack... all good now mine is fixed as well.
Great Video, worked for me, only comment to those that are trying this for the first time. I soldered the wrong terminal because my piece broke off and soldered to the other side. I was like that's was easy, then I tried the light and it didn't work, so I watched the video again and realized I need to melt the plastic on the upper section a bit more to expose the broken section. I presume this accident was good otherwise I might have shorted the light.
I fixed my tail light a couple months ago and now the middle section of leds is out. The light between the two fix spots. The lower spot appears to have the two tiny bridges separated but when I connect the lowest bridge the section of lights below it go out. Am I in the wrong place?
I know Im randomly asking but does anybody know of a way to log back into an Instagram account? I stupidly lost my password. I would appreciate any help you can give me.
Have a 2017 Denali XL same problem, dealer covered the driver side replacement but wasn't going to cover the passenger side that crapped out about 3 months later. Followed this video, took me about an hour start to finish and the taillight is working perfectly now. Thank you for posting this!
Same here.Can you tell me more about the where and when of this shark? I would love to identify it based on the spot patterning and track it over on whale shark [dot] org. Thank you!
Ashraf.... Do you think if the post that holds the board was melted down, Would this prevent the tin strip from snapping?
This worked for one of my tail lights. The other only has brake lights working now; still no parking light. Any idea what’s wrong?
You the best
How do I get a hold of you
Looked so easy in your video. My soldering iron didn't cut it just melted and I ended up ruining the board. Think I should have used a dremel and cutting disc.
Thank you and if your hand is shaking it’s time for a drink 😉
what city are you living? I want to send you or bring you my GMC tail light.
Thank you so much for posting this video!!! I spent $6.00 on a soldering iron!
Thank you for this video…I fixed both my tail lights and it was a lot cheaper than 800 bucks for new ones….thanks so much!
i need to sent a light we have few leds in middle not working
Anyone that don’t wanna waste time with rebuilding the lights. Go to your GM dealership and tell them you want the revised part number tail light. The tail light is $205 through factory GM. Make sure to tell them you want the revised number. There was a recall on these for the 2015-2016 with the vehicle under 75,000 miles and they changed the light number
There are other videos with much better techniques and methods to repair the tail light in one video.
Thanks. Good repair procedure. Using iron to melt plastic good idea.
How do you know where to open the light to commence the repair? I am having a similar issue with Drivers Tail light working intermittently. Any advice would be appreciated. Your work is by far the best I have seen here on you tube.
Is amazing we as buyer have to do this crap because the LED strips GMC or Chevy use are very low quality. For an over 60k vehicle? Hahaha there is no shame.
Video is awesome and very thorough. How ever I didn’t see I this video until too late. First passenger attempt worked but middle 6 +/- bulbs are still out. Anyone know how to repair this?
Hey, same thing happened to me after trying to fix mine. The middle row went out. Did you ever figure out how to fix this part?
Same with me it was particularly fixed, wondering how to fix it as well.
@@mitchvillemaire8051 I finally fixed mine. After reading through hundreds of comments I finally figured out I had soldered the big gap section together. This causes the middle section of the taillight to go out. Only solder the hairline crack. If you did this go back in and cut the solder back out. This comment by Tom Maddox help the most Dude! You just saved me $800! Thank you! Great video. Explained well. The only thing that threw me was that the plastic was attached to the metal on the circuit board at the point of the hole you used to anchor the wire, so when I pried up my cut out, it was pulling on the metal. What threw me was a small metal "Bridge" appeared to connect both large pieces of metal. It looked like one end had cracked off and I figured I had broken the connection when I pried it up so I soldered that as well as the main break you show here. When I tested the light, the middle LED's did not light up. So I de-soldered the small "Bridge" and bent it out of the way so as not to make contact and that did it. I am still trying to figure out why that piece was there.
@Rodney Austin Thank you! For some reason when I applied 12v to that section I heard a small pop then it worked.. so it must of had a short some where. Since I only fixed the crack... all good now mine is fixed as well.
Would really appreciate it if people could put pressure on GM to build better circuit boards in the first place.
I need a 2015 passenger side light repaired . Can yo do it?
Great Video, worked for me, only comment to those that are trying this for the first time. I soldered the wrong terminal because my piece broke off and soldered to the other side. I was like that's was easy, then I tried the light and it didn't work, so I watched the video again and realized I need to melt the plastic on the upper section a bit more to expose the broken section. I presume this accident was good otherwise I might have shorted the light.
Just saved me $$$. Thank you so much!
I fixed my tail light a couple months ago and now the middle section of leds is out. The light between the two fix spots. The lower spot appears to have the two tiny bridges separated but when I connect the lowest bridge the section of lights below it go out. Am I in the wrong place?
Having the same issue right now
Awesome video. Thank you so much. I was able to fix both lights on my yukon in less than two hours saving $1300+
I know Im randomly asking but does anybody know of a way to log back into an Instagram account? I stupidly lost my password. I would appreciate any help you can give me.
@Corbin Reginald Instablaster =)
Do you sell the tail light assemblies/refurbished?
Have a 2017 Denali XL same problem, dealer covered the driver side replacement but wasn't going to cover the passenger side that crapped out about 3 months later. Followed this video, took me about an hour start to finish and the taillight is working perfectly now. Thank you for posting this!
Where did you purchase the light?
thats either a whale shark or a basking shark so it wouldn't've done anything but thats still an amazing thing to see. especially that close.
That'll be one disappointed shark - there's not much meat on an ROV.
Same here.Can you tell me more about the where and when of this shark? I would love to identify it based on the spot patterning and track it over on whale shark [dot] org. Thank you!
Hi there, can you tell me where and when you saw this shark? I may be able to identify and track it on whale shark [dot] org.
this video was taken by Oceaneering rov at the depth of 140 feet during a repair operation in the gulf of Mexico
Ashraf bechai Was that this year?
Oct 2005
Ashraf bechai Marked this shark as CRB-014 over at whale shark [dot] org. Let's hope we see it again in the future!