Відео

That’s furniture for your home

Sieht gut aus!👍

Load overbearing music earns you 👎

Scares the sh1t out of me how close your hands get to that router....

Haha, don’t know why this came up as I asked for DIY shaker plywood pantry. You have a shop with $30k of tools, hardly a normal DIY.

They're beautiful design but extremely overpriced

Question is how much did it cost?

Very nice work fella! What did you do to get the table saw burn marks off the edges of your glue ups? You could set your router up as a jointer perhaps.

Thanks for posting. I’m replacing some broken glass in a curio cabinet with copper mesh. My gut said to use staples, so it’s nice to see it worked for you.

I need one of those made how can I contact you

so how does the free floating layout perform?

Great video. Great demonstration you have talent my friend

0:52 it wasn't that easy to get it to fit my old right tilt grizzly cabinet saw had to enlarge the end holes to get the surface to be level. I think I might have to add some support legs to ensure that it doesn't flex while under strain of holding up heavy timber.

Interested in doing this too. I noticed that your CNS has the Contractor Saw Mobile Base, has adding the weight of the router assembly made it any more difficult to maneuver? TIA

I've been trying to figure out what to do with my excess carbon fiber!

It's truly a work of art but has no equipment rack

Nice job and bench too

Have you ever considered doing a whole kitchen?

I like the way you inlaid ZEPHYR

Looks good! Countersinking those brass screws then giving the brass a brushed look would have been nice to see.

That is a lot of money in Maple Lumber. Wonderful project.

Thanks for the video! Couple questions if you have the time. How did you remount the power switch? Did you drill new holes in the router table? Did you mount the router table to the rails? Did you drill new holes in the table or the rails?

Not bad bro!👍🏽

looks great. lemme get one. i have pizza.

I have this extension table router table, also. Best money I ever spent, and I've had it for over 10 years.

Awesome work! Talented young man! Coming from a not so talented old man who appreciates talent and quality work!

You're genius ！❤

Just started watching. Audio goes from normal voice to jet engine loud.

Wow this looks amazing. Does it breakdown into 2 components for transport or is it more of a permanent install

Nice

Super sweet build here! Learned a couple things!! Some criticism from another creator… try to work on your volume levels in your edits. Your vocals are super quiet and the saws/planer sounds are super loud. Try to even them out. I found myself having to raise and lower the volume through the video. Informative and good video! Subbed! Will love to see you grow 😄 Cheers!

Not sponsored by Ryobi

Skills..

I could only lift 50lbs does it weigh more than that?

These are really impressive! How did you end up finishing them? I am most likely going to go with a shaker maple look for my own kitchen cabinets, but I’m not sure I’m as ambitious as you are to use solid wood!

Why did you decide to move from the left to the right side? I'm trying to decide what the pros/cons would be before I install mine.

I got so excited for a moment, but I just checked your website and wtfu... You need to design it so cables aren't visible to the people. They need to go through the stand and to the controller. The photo you got on your website is pure garbage, i don't even know why you would use it as advertising material. Go check out bunn gear for inspiration and just do that.

Sweet but how much for the labor? and how many hours did you take? 22days x8?

You never mentioned that you replaced the bolt to attach it on the CNS cast iron, unless you forced the available bolt that comes from Benchdog or re-tap the thread on CNS cast iron

I have seen the progression through your videos. You have some mad skills and great design ideas! I enjoy watching you build and not interrupt with nonsense talking unless needed. I do hear dust collection running in the background - what do you use ? It looks like it is working well.

One quick question, what about the switch of CNS, is ut on same place used to be? And also does this have a particular switch also? Thanks for your reply and video 🙏🏼✌🏼

Exactly same model I need to see! ✌🏼🤙🏼🤘🏼👍🏼

Great video! After using this setup for a year, are you still happy with it? Anything that you would do differently? Thanks.

Nice shop and nice work.

Check out our website if you’re interested in purchasing a table or just to check out the site. custom-dj.com Thanks- Drew

wow your work, Amazing. very clean. awesome wood. all your video. DJ BOOTH SO COOL

nice work

great stuff, thanks for the dentist sound

Slick

Awesome!