Відео

Rain X Works

Did ya get message sent ya....had couple questions..

Where located???

Need plans for that boat

With having to watch all the early vids, I'd like to know what diameter your pump is and what motor,( inrunner/outrunner lengh, dia. K V rating.) And like others stated, batts c rating needs to be high. I was running my diy disability scooter at 10S but was unhappy with my top speed and run time so bumping it to 20S didn't just get me double the top end but added about 50% to my run time if using near full throttle and even more around 2/3's or less. 37 mph on a 12" front wheel is very hard on the nerves. Next one will have 20" at least wheel size.

$0.02 = Watch some "World Jet Boat" Racing. Like the Salmon River races Pause on a boat getting air and see what the bottom of the boat and intake look like. Watch the show n shine to see what the jets output looks like. ( stove piped down to be smaller and moved to the bottom side to be at lowest point. And rc boats I've done, using a ride plate to make it seem longer and protect the parts outside the boat. Helped a lot. Enough motor and it should be sucked to the surface of the water having only the intake riding on it.

How did you design the structure

Hey bro, I first seen your videos a couple years ago and I got one thing to say, I love it. Any improvements to the intake? I know it's been a while. But if you haven't I think I might have the solution. Let me know. Thanks for the inspiration, I just got to get the fab skills now, lol.

Hi, i need to get in contact with you about the jet drive. I need to source one or get some info. Its for a senior design project.

ua-cam.com/video/LUjgNP3a_nU/v-deo.html

.. the components are to heavy for the hull

jet pump is too big for the boat, not enough weight to get the water up to the impeller quick enough.

I bought a few different types of membrane pumps. low volume compared to your pump but zero problems with sucking up water. and even could place a bigger one compared to mine since your boat is also pretty big. then you have no problems with sucking it up and have a good flowrate. Can you tell ke what sensor you use? is it on and off of does it activate a timer when running?

I know I'm a little late to the party but you've done something that I've been wanting to do for years. I just don't have the talent/skills. What ever happens to this boat? You still have it? Great job on it by the way.

I don't know if it is a 3d printed jet or not but first things first. The scoop I believe would cause a good deal of drag or resistance in the trade off for more water. It's just physics. The reason I asked about the 3d print is maybe The intake could be redesigned so that it doesn't make the water go up and out. Instead just have the jet pretty much flush with the bottom of the boat and have the intake on an angle, say 20-30 degrees, thus not making the water have to go up and out. It would be more like in and out which would work great in theory because there would be no resistance and you would be alleviating more resistance by providing a more straight forward path for the water to travel. The other thing to keep in mind is the intake pretty much becomes a vacuum when the internal prop is rotating, so much so that it doesn't really need any assistance in getting more water. The only thing that will increase the speed and mass of water entering the jet is the speed and mass of water exiting the jet, so more power is the only thing that will work in combination of making a more streamlined path for the water to travel. Hope this helps.

Are you still building??

Great job mate

I know it been 5 years since uploaded but I what to build this beast please send plans

That is 1 hella of of a boat mate , wow nice well done🤙🤙🤙😊

Kool

Any dimension for the hull ?

Very nice setup. I need one for my boat. What pump water sensor and one way valve you using?

I watched a video some time ago of a guy converting a shallow draft skiff into a jet boat. He had the same issue. He solved his problem by designing/building a bulge into the haul on the keel if the skiff just before the pump inlet and I believe he just used automotive body filler and shaped a bulbous shape and it solved his problem. This comment is probably a day late and dollar short.

Hello. I know I’m a little behind, but what are the chances of you still being able to make one of these still?

Excellent run 👍

Excellent job 👌

😁Ну и нагородил!!!!🤔

Kalau harga berapa...?

I had a similar experience with a 60 meter long real navy boat using real waterjet. In the case, ridiculously expensive side fin stabilizer didn't help at all. Amazingly, a simple fin at the tail of the boat solved the problem and yes riding at 100 km/h was a thrilling joy.

How does it perform on the water?

Eliminate the flat bottom on the hull, the water density is to low that is being delivered to the pump. Once you are at 3/4 to full throttle it is sending bubbles strait back to the pump due to the flat bottom, try implementing a dead rise all the way back to the to the pump so that the bubbles that are being created by compression are shuttled off to the sides giving a dense stream of water to the original grate. outboardjets.com/boat-selection/

Cay đó mua ở đâu vậy anh

Dimana sy bisa membelinya?

Building a scale boat and was curious about the jet drive and where it was purchased and the diameter of the output and thrust capability of it

A pleasure to watch!

How much for build plans

Sir can u please show this beutyful boat video inside of photos can I please show it in a explaintion video from part 1 please sir I all so want to do this type of please sir please it will be a big all people who are whiching ur videos

Put a spoon under the kitchen faucet with the handle straight up, water down the back of the spoon= shape of hull before intake!

Boat speed

Hi Friend - Great Job on the completed project ! I’ve been looking for a Mozzie Craft boat for years. Can you tell me what happened to the company and where I may possibly purchase one ? Thanks much !! Luzine

Hello Brian, do you have any drawings on this amazing build?

Verry nice!

I found that the little 9v pump out of a desktop fountain works great

any footage of how you made it? - i mean i know most of it is pretty simple.....

How much did it cost to build?

It looks like this jet drive nozzle just has a lot of drag or maybe has no good flow when steering. Maybe if you put a riding plate underneath to extend the mid of the keel backwards under the jet nozzle it will be a smoother ride without al the splashing. and maybe it is just the design of the nozzle. eigther way. It looks like a heavy duty unit but performance looks a bit off. Maybe I am wrong.

Is this guitar still playable? Cool idea though!

Where can I find the jet motor mount?

It has to much power to get a good, strong and steady water flow. if you crank up throttle to spin up the prop to suck more water, it wont happen. Your motor has to much rpm in this configuration. it just to powerfull for something like this. If you use a bigger prop with this motor is will make you faster. full throlle and it slurps..Its like makeing burnouts on the road with a car, if you hit full gas, your cat wont move fast, it just spins out where it is.