Відео

Thanks. It’s wood effect vinyl.

What fans do you have?

@@KoolPCsthe rs120 argb fans, the ones that came in the case. I found out how to change the colors but do they lights stay on all the time? Even when it’s off?

@@aaronr.3032the RS fans plug into the motherboard and will be controlled by your motherboards RGB software.

RS fans are plugged into the motherboard so iCue won’t see them. You need to use motherboards RGB software

Thanks. It’s a EZDIY-FAB vertical mount from Amazon.

I connected them in 3’s so used 3 PWM headers on the motherboard.

@@KoolPCs Thanks, but wouldn't it be easier to connect them all in series and then on a single header? Or is that not possible?

Easier yes, however 2 reasons you may not want to do that: 1. You may want to run the sets of fans at different speeds. In my example build, I’m running 4 intakes and 3 exhaust, therefore I would want to balance the airflow appropriately. 2. This is the most important consideration, PWM headers have a power rating. My headers support up to 1A, and the RS fans are rated to draw 0.18 A, so I would only be able to get a max of 5 fans pers header.

@@KoolPCs OK I see, thank you

It’s an Asus Tuf 4080 super. 348.2 x 150 x 72.6 mm

Unlikely unless you do something stupid like try to build on a tile floor or something

Yeah should have been included as standard.

No, this is the Teak.

You don’t need a vertical bracket for it. The PCI-e slots rotate so all you need is a riser. I have made a full video overview of the case, check it out.

I’m really impressed by the performance of the fans. I have since purchased a 140mm for the bottom intake and moved the 120mm that was there to the back. I have also installed a custom loop (check my shorts or Reddit posts). Correct they can be motherboard controlled for both PWM and RGB but I have switched to a commander pro since switching to watercooling as it’s a lot easier setting fan curves to coolant temp using iCue.

Which fans do you have? These are the RS fans. They connect to each other then finally into the motherboard. You then need to use your motherboard’s RGB software to control them.

The 570 is a lovely case, but the 3500x will likely give much better airflow. Depends on your needs really.

Temps were great in this air cooled build, but the RS120 fans no doubt played a part in that. I have watercooled it now (check my shorts) and am super impressed with the temps. Coolant maxes to around 37° and it’s totally silent.

There is plenty of space. More than the 5000, I have used both. Fans I’m using aren’t iCue Link.

Never mind

Hopefully the video helped 😀

Yeah the feet are removable, but the case would then be sitting on the dust filter. If you invert the PSU so it intakes from the case and don’t use the bottom intake fan then you can remove the feet and dust filter.

Glad you enjoyed it

Thank you. Glad you enjoy my content. ❤️

Thank you. Appreciate the feedback. I’ve done a similar overview of the upcoming Corsair 3500X too.

@@KoolPCs I will look for it

Really appreciate that, thank you. Glad you found it useful. Still very new to YT and I tried to include things that I would like to know when looking to purchase a product like this.

The gap between the psu and the fan on the bottom would be minimal so you should put a 140

Personally I don’t think it’s worth it. There is very little gap between the PSU and the shroud for air. 140 at the bottom is a better option. I will be putting a 140 in once it’s release. Check my latest Reddit post where I have put a custom loop in the 3500x

@@KoolPCsyea I got a 140 for the bottom too when my case gets here. i was only thinking to add those two so complete the 10 fans. I would like to see your test with those fans on the psu shroud if you thought of doing that?

@@KoolPCsand will do 👍🏿

@@Sanni_VSno can do as I’ve now vertically mounted the GPU block.

Thanks mate

I'm glad you enjoyed it.

Perfect!

Thank you!

I just uploaded the final video of it today 😀

What do you mean?

@@KoolPCs looks poor not strong than another vertical GPU mount

@@maxsunz3703 it’s exactly the opposite. Proper solid. Also attaches to the motherboard tray so no sagging. Shame that it’s not possible to fit a radiator and fans under it otherwise would have happily used it for my build.

@@KoolPCs and price so expensive than another vertical GPU mount -_-

@@maxsunz3703 Not justifying the price but it does come with a high quality riser cable, is custom made to fit the case and is of high quality itself. I had to use a 3rd part mount which was slightly cheaper but had to trim the PCI slot covers to make it fit.

Thanks. Yeah it’s a great case. Stay tuned for my upcoming build in it. 😃

Never had a 980ti. Used to own a 1080ti that I modded with a 120mm AIO. Sold it when I got the 3090.

@@KoolPCs quite nice upgrade

The 3090 PCB is missing 😀. Using it in another build with a waterblock.

Sold it a while ago to get the 3090.

OG legend will always be 8800GT back when crysis came out i think.

@@ARUNMANOJ86 have a couple of those in SLI. Good times!

Which are they?

Had a 1080ti but sold it 😭

You got it! 😂 it’s currently in use in my PC with a water block on it.

Watercooling is an option, you don’t need to do it. For me it’s a hobby.

Yeah it’s my current build. Couple of years old. New one coming very soon.

Nothing is wrong. 40°C at idle is absolutely fine. What matters more in watercooled builds is the coolant temp.

Anytime

Thank you. Yeah I loved this build. Another new full build coming soon!