Відео

Can I have your number

What brand

Very nice explained..thanx.

Motor auto run

Hello, tiking always. And 1 tik it will heet n nxt tik seems like cut off. Seems like on and oFf every seconds. It's getting hot but slowly. Can you please help. Thanks

sir ic 2003 to inlet and drain which resistance value Sir

El que tengo, no prende ni el ventilador, solo suena un pitido, prende las luces y al minuto se apaga

Drain ic replacement. Is ic same as inlet valve ic wiring

Bro really helpful and way of explaining is really understand able

mera machine ka inlet direct ho geya. power on karneke sath sath valve active ho jata hay. may ne inlet valve change kiya, valve ic change kiya resistor check kiya jo kharap tha who bhi change kiya.phir ye problem aaa raha hay. kya kar sakte hay can you please explain me?

same problem facing. but my washing maching work perfectlybut only inlet valve not working. but when i put water manually then it wash everything perfectly. I changed the inlet valve ic but still not working. what should i do?

sir this 20 pin ic pin 20 voltage and smd resistance value as voltage devider

My inlet valve is ok but continuously it is getting 220volts from pcb what might be the issue?

Acst 10357 me dusri konsi ic chalega

Very very thank you sir.

I have same PCB board in machine. Everything is working but during washing and rinsing the timer gets stuck and blinks once every motor trigger. In short it keeps on washing and rinsing with a relay trigger sound and all lights blink once ever trigger.

Panasonic front load washing machine NA123 vb3 shows 'END' message as soon as the wash selector is set and door is not locked with outlet motor starting. Pressure sensor is good. Pcb board no AXW24V-18738

Adrees

Plezz drop apka phone naumber

prestige pic 6.0 v2 buzzer continuous beep and stoped working

I have E1 error code, checked with 10k resistor, and bought a new thermistor, but it was not the problem: 240kOhm @ room temperature is ok. The problem is at integrated circuit in main PCB. Analog input AI3 (P63) should be high impedance (it is also tristate digital I/O), but it was latched at Vdd=5V. Solution A: replace main PCB (150€). Solution B: desolder pin 51 (it seems to work, I do not know how reliable). Solution C: replace thermistor with 10kOhm resistor or even thermistor (but then temperature readings will be wrong, i.e. insecure operation, discouraged the use of convection, only microvawe). Look for C139ST service manual, very useful for me.

क्यू ऐसा होता है? Pigeon acer plus induction error E6 बताता है E6=the heat sensor of igbt radiator temperature is overheated

Telugu

Cool

New mother board se ahi problem ay Rahi he

Sir very important video my pcb sem problem 100k r Cheng and working OK sir Hindi language Im not English Thank you very much

Thanks for the video

Sir one problem is in LG TOP LOAD washing machine inlet valve have continous supply when machine main supply on means water continue on so if i checked at valve continous supply shown so pls suggest solution is it possible triac is on when main supply on. Is it possiblw when triac shortckt it may continues on?

did you say 10K resistor you can bypass for the E1 code? hard to catch it. thanks

Is it the only reason ? We bought a new one and it suddenly made such noise what could be the reason ?

So if fan is working problem is in capacitor

Hello I hope you can help I have an aobosi one and has no power i can't find the MOSFETs exact match online

Sir, I have similar problem. Everything looks perfect on tge pcb, but tge drain motor and pump are not working. What could be the source of the probkem?

I bought prestige induction stove today online.when I connect the plug to power it made sound first time.induction stove is heating for 5-10 seconds after that it is not heating.i used junction box also still no use.some sort of sound is coming from inside the induction like screws sound and parts are sticked.please give solution

Hello sir... My board is same sir..... Problem is water valve not opening sir... Valve changed... But no use. Power continuesly coming to valve... Sir but how much voltage coming to valve i don't know sir... But valve not opening.what is the problem sir

My board is same sir..... Everything ok but water not taking..... 4E error... Water valve changed... But water not taking... Plz reply what can i do

Sir..... my problem is that I replaced 2x dead hot and cold ACS TRANSISTOR with BT136 and now the water solenoid and drain is always on...

Sir appreciate more if video is zoomed to the PCB

I have checked the voltage and it's 331.. even them I am facing non heating issue...

Sir mera yahi pcb hai but usme inlet valve direct on ho raha hai, inlet valve ka trasistor bhi ok hai dusara laga ke bhi dekha but same problem, please solution please

Nice Video...

वगेर मेमरान वदले se. इरर कैसे निकाल सकते है

For the non technical user, if your stove is continuously beeping and not heating it’s usually due to two things: 1. Your cookware is made of non induction material such as aluminum, brass or copper. Electrical induction stoves work well with stainless steel cookware. 2. Your cookware doesn’t have a flat surface so it’s not touching enough of your stove to start heating. And one more, altho this is obvious for most people, you haven’t placed any cookware on the stove or you’re misplacing it (not aligning it correctly with center)

Sir Hindi translation

no sound

Please tell other reason micro no output

Nice informative information

My induction is heating. But continuously beeping. What is problem.

Thank you sir

🅰️🅱️🕉️🕉️GOOD TEACHING FOR YOUR CHANNEL🚦THANK YOU SO MUCH VERY VERY GOOD 👌